Manual Hendi 232804 (page 120 of 128) (English, German, Dutch, French, Italian, Polish)

742380

120

Zoom out

Zoom in

1/128

120

The manufacturer and dealer is not liable for any

inaccuracies due to printing errors or transcription,

in this manual. In line with our policy of continuous

improvement products, we reserve the right to make

modiﬁcation of the product, packaging and speciﬁ-

cations contained in the Documentation without pri-

or notice.

Before the first use

Transport

• Special package box is required for the delivery of

the equipment. Keep the equipment level during

transportation and handling.

• Please carefully check the package box after re-

ceiving the product to ensure that the equipment

is not damaged during transportation.

• Check for the completeness of the equipment. In

case of incomplete delivery and damages. Please

contact supplier (See ==> Warranty).

• When removing the package box, carefully move

away the wood plate in case of scratch the equip-

ment.

• In case that the equipment tilts during the trans-

portation and handling, the lubricant in the com-

pressor may flow into the cooling loop. Therefore,

in order to ensure the lubricant flows back to the

compressor, it is necessary to keep the equipment

level for 24 hours before plug in the equipment

and starts to work.

• Do not throw away the package randomly. Please

dispose as per relevant local rules and regula-

tions.

• Clean all components as described (See == >

Cleaning and Maintenance).

• Place all the shelves inside the appliance.

NOTE: Due to manufacturing residues, the appli-

ance may emit a slight odor in the first few cycles.

This is normal and does not indicate any defect or

hazard. Make sure the appliance is well ventilated.

• Turn on the lighting switch, check the light is nor-

mal.

• The digital temperature controller is delivered

with default parameters. Do not alter the param-

eters casually except for special need.

• When running for the first time, it should run

without load for 2 hours to ensure the refriger-

ation system is working normally. Only when the

temperature within the appliance is reduced with-

in the indicated scope can the food be put into the

appliance.

• Don’t put too much food in the appliance to pre-

vent instantaneous high load. The food shall not

block the air outlet and air inlet. Nor shall it be

close to side glass. Otherwise it will lead to con-

densation.

• To keep the taste of the food, please have the

equipment running 24 hours a day.

• During the frosting process, the temperature of

the appliance may rise slightly. When the frosting

end, it will return to normal.

ATTENTION: During transport, avoid skew the unit

from the vertical by an angle greater than 30 °, If

necessary, wait approximately 3-4 hours before

running, until the oil flows to the unit. Otherwise,

the condensing unit may be damaged.

Levelling

To ensure correct functioning it is important to level

the appliance. Correct levelling allows for reduction

of vibration generated by the unit in operation.

Thoroughly check the levelling with the use of a

spirit level.

CAUTION!

To ensure proper functioning of the cooling/freezing

appliance, strictly follow the instructions below:

• Do not put the appliance in a place exposed to di-

rect sunlight and near appliances emitting radi-

ation, such as: heat lamps, stoves, radiators etc.

• Avoid integrating or building over of the appliance.

• Do not place any objects on the top of the appli-

ance housing where the refrigerating unit is lo-

cated.

• Do not place the appliance in a room with relative-

ly high humidity (water can liquify on the housing).

• Do not place the appliance in narrow recesses (if

there is no air circulation, the appliance will not

function properly).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 232804 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 232804 Manual

Product: