Manual Hendi 232170 (page 16 of 176) (English, German, Dutch, French, Italian, Polish)

742362

Zoom out

Zoom in

1/176

ATTENTION!

At the end of the positive process phase, the con-

servation program is set automatically at the tem-

perature of 0 to +3°C.

At the end of the negative process phase, the con-

servation program is set automatically at the tem-

perature of -22 to -25°C.

In order to respect the chilling and freezing time

provided by law, while a cycle is in progress, it is

strongly advised against opening the door of the de-

vice.

Alarms

The existing alarms are those related to the probes.

They are shown only when it is required the view of

the relative probe. “Er” Generic or internal error of

the probes.

“Er” generic error or inside the probe

“ErI” room probe error

“Er2” core probe error

If one program is in progress and an error is gener-

ated, the cycle passes to time process even if the

error continues to be on.

Regulations

Compressor

The compressor can be active only in START func-

tion when the room probe has no error.

If the presence of door is on (PI=I), the door must be

closed to permit the starting of the compressor only

if P6=0. With P6=0 the compressor is active even if

the door is open and with arrested fan. The com-

pressor starts according to the SET POINT on, cor-

responding to the selected cycle and according to

the differential of temperature set (Parameter P8).

The protection time for the compressor are:

• P9: minimum delay that must exist between the

switching off and the next starting up of the com-

pressor. This parameter is used also like reset of

the card.

• P10: minimum delay that must exist between 2

consecutive starting ups of the compressor.

Manual defrosting

The defrosting is carried out with open door, without the use of neither the heater nor the hot gas.

Parameters

Pressing contemporarily Up and Down to en-

ter the parameter setting for at least 4 sec.

At this point on the display appears the number it-

self of the parameter (P0). Pressing the SET

SET

key,

it is possible to see the value of the parameter itself

and modify it.

The keys Up and Down , when the parameter

setting is on, allow to pass to the next/former pa-

rameter; when the value of the parameter is on,

they modify it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 232170 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 20,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 232170 Manual

Product: