Manual Hendi 230299 (page 6 of 124) (English, German, Dutch, French, Italian, Polish)

742484

Zoom out

Zoom in

1/124

• Remove the protective foil protecting the steel

housing of the dishwasher from scratches. Any

remaining adhesive residue should be careful-

ly removed. Do not use any scouring materials.

Leaving the protective foil can cause difﬁcult to

remove adhesive glue foil to the dishwasher’s

steel housing.

• The appliance should be placed horizontally.

Possible inclinations should be corrected using

a spirit level.

• Following the successful installation, the dish-

washer should be cleaned thoroughly with a con-

ventional detergent before it is put into operation.

Connection to the water supply

• ATTENTION: The connection with the water

supply should be made according to the current

safety standards.

• The dishwasher may be connected only to a cold

water supply.* (In case you want to connect it

to a hot water supply, please contact our com-

pany)

• The water supply hose should have a ﬂap valve

(non-return valve) according to DIN 1988.

• The water supply hose/pipe should be rinsed be-

fore the appliance’s connection.

• The water supply hose/pipe should have a min-

imum internal diameter of 16 mm and the con-

nection with the hose should be 3/4 inch.

• All hose collars should be adjusted in a ﬁxed po-

sition before the appliance is put into operation.

• The dishwasher can be only connected to a

well-functioning softener.

• ATTENTION: The water pressure must be be-

tween 2 and 5 bar.

Drainage connection

• The outﬂow is accomplished through gravity

force (natural ﬂow). The outlet hose should be

connected either directly to the main drainage -

where a pipette for odours is anticipated, or wa-

ter runs directly to a drainage well in the ground,

which has a pipette for odours.

• ATTENTION: The outlet hose should not be

placed higher than a level (as given for each ap-

pliance’s type) from the lower side of the dish-

washer’s dispenser.

Electrical Network connection

• ATTENTION: All electrical work must be carried

out by a suitably qualiﬁed and competent person.

• The dishwasher operates under speciﬁc voltage

depending on the type of the dishwasher.

• You should supply the power, depending on the

appliance’s power reception (the electrical con-

nection should be made by authorized electri-

cians). Speciﬁcations should be met according

to the corresponding parts of DIN, VDE, D100,

the EVU connection terms, the relevant ZH 1/37,

chapter 7.2 - as well as the current speciﬁcations

for accident prevention.

• Respectively, the appliance must be connected

to a direct power supply electrical installation

through an HO7 RN-F cable with load relief of the

appliance.

Protective duct connection and voltage compensation

• The electrical safety of this appliance is ensured

only if the protective duct has been connected

and checked properly. The corresponding spec-

iﬁcations should be met at this point (see para-

graph 1.5).

• In addition, the appliance should include a volt-

age compensation system.

• For this reason, the backside of the appliance has

a screw with the indication “voltage compensa-

tion”.

• Following the electrical connection, the action

of the protective duct, the voltage compensation

and the insulation value should be checked ac-

cording to the existing provisions of DIN VDE.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 230299 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 230299 Manual

Product: