741924
11
Zoom out
Zoom in
Previous page
1/44
Next page
11
EN
The fi rst commissioning must be carried out pro-
ceeding as follows:
clean the front part of the oven with a clean
and soft cloth in order to remove any eventual
residues;
connect the plug to the socket;
put the switch of heating elements (pic.3;4;5-
ref.3) in pos.”i”; for the ovens 1/40 and 2/40: press
the general switch (pic.1;2-ref.7);
Start the heating elements setting the thermo-
stat (pic.1;2;3;4;5-ref.2) on the temperature of
150°C. The red warning lights signaling the op-
eration of the heating elements is on;
let the oven heating up for about 1 h;
switch the heating elements off by putting the
switch in (pic.1;2;3;4;5-ref.2) in position “0” the
warning light turns off; for the oven 1/40 and
2/40: press the general switch and turn off the
heating elements;
open the door and keep it opened for about 15 min
in order to let steam and smell to go out;
close the door and repeat the process de-
scribed in section 4) bringing the thermostat
(pic. 1;2;3;4;5 -rif.2) at the temperature of 400°C
for the oven 1/40 and 2/40: bring thermostats
(pic.1;2-ref.2) at a temperature of 350°C.
let the oven heating up for about 1 h;
switch the heating elements off by putting the
switch in (pic.1;2;3;4;5-ref.2) in position “0” the
warning light turns off; for the oven 1/40 and
2/40: press the general switch and turn off the
heating elements;
turn off the oven as described in par. 5.4
with the oven 1/40 and 2/40 you can adjust the
cooking time by setting the minutes with the
timer (pic.1;2-ref.6). at the end of the time set
the heating elements will turn off. To choose the
mode of cooking continued, bring the timer knob
(pic.1;2-ref.6) to “on” by turning to the left
5.3 TURNING ON OVEN
Connect the plug of the power supply cable to the
power supply outlet;
Put the switch of heating elements (pic.3;4;5-
ref.3) in pos.”i”; for the ovens 1/40 and 2/40: press
the general switch (pic.1;2-ref.7);
Start the heating elements setting the thermo-
stat (Pic.1;2;3;4;5-Ref.2) to the desired tempera-
ture indicated on the handle. The related warning
lights signaling the heating elements in use are
switched on;
Once the oven has reached the desired tempera-
ture (see point 9 of this paragraph), visible on the
thermometer (Pic.5-Ref.4), it is possible to insert
the pizza;
Open the oven door manually using the handles;
To illuminate the inside of the chamber, press the
oven lamp switch (Pic.5-Ref.5);
Insert the pizza/pizzas using suitable devices. It
is important to avoid leaving the door open for too
long, since the outgoing heat lowers the temper-
ature of the oven.
Close the door again and check the backing
through the inspection glass ;
The baking temperature of the pizza varies if it is
positioned directly on the refractory stone or on a
baking tray. In the fi rst case, it is suggested to set
the backing temperature at 280°C on the bottom
and 320°C for the ceiling; in the second case, set
320°C for the bottom and 280°C for the ceiling;
When the baking process ends, open the door
and extract the pizza /pizzas and colse the door
again.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 226940 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 226940 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info