Manual Hendi 225059 (page 5 of 36) (English, Polish)

741835

Zoom out

Zoom in

1/36

• a omnipolar switch with minimum between-con-

tacts aperture of the overvoltage category III (4000

V),

sized to the load and conforming to current

legal regulations, is ﬁ tted between the appliance

and the mains in the direct connection to the

mains;

• the omnipolar switch used for connection is easy

to reach when the appliance is installed;

• the yellow/green earth wire is not interrupted

by the switch;

• the power supply, when the appliance is operat-

ing, must not deviate from the rated voltage value

by ±10%;

• make sure that after inserting the power supply

cord into the terminal block it does not come into

contact with any of the cooking range’s hot parts.

• if the supply cable is damaged then it must be

replaced by the manufacturer or by your tech-

nical support or by a qualified person to avoid

any risk.

Connection to the water mains

(for ovens predisposed to humidiﬁ er solenoid-valve)

The appliance must be fed with softened drinking

water, with pressure in the range from 100 to 200 kPa

(1.0

- 2.0 bar). Water must have hardness from 0.5°F to

3°F (it is suggstible to use a softener as to avoid the

malfunction of the fan, the breakage of the heating

element and to reduce the formation of lime inside

the cooking chamber). Connection to the water

mains should be made through the threaded 3/4”

solenoid-valve on the rear (on the bottom) of the

appliance, ﬁ tting in between a mechanical ﬁ lter and

an on/off tap (before you connect the ﬁ lter, allow

a certain quantity of water to ﬂ ow out in order to

drain any waste from the pipe).

Connection to water tank

(for ovens predisposed to water pump)

To replace electrovalve with water pump (in ovens

with

optional predisposition to pump), follow the

steps below listed (image 1):

1. Remove back cover from oven.

2. Disconnect wiring cables from electrovalve.

3. Disconnect water tube (3) from electrovalve,

pressing e keeping pressed the edge of black

linking (quick insertion).

4. Remove the electrovalve unscrewing the screw

that ﬁ x it to oven’s frame.

5. Fix the pump (1) to the frame with the appropri-

ate support (2) and the two screws (4) included.

6. Connect the cables previously disconnected from

electrovalve to pump.

7. Connect the tube previously disconnected from

electrovalve to pump’s linking.

Connect the tube (6) with ﬁ lter and ballast (includ-

in “Pump kit”) to pump’s apron (7).

9. Replace back cover.

Warning:

To avoid limestone buildup into the cooking chamber,

we suggest to ﬁ ll the water tank with decalciﬁ ed water.

Check water level in the tank before activating the

pump and during its functioning. If pump works with-

out water in the tank, what occurs is abnormal noise

at first and then its breakage.

Fig. 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 225059 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 225059 Manual

Product: