741885

Hendi 223256 Manual

22
Zoom out
Zoom in
Previous page
1/56
Next page
22
EN
SPEED REGULATION
To regulate fan speed press the speed button and
acting on the encoder you can select two different
speeds: minimum or maximum. You will see that
on display will appear min or max and you confirm
pressing the encoder button.
START/STOP
This button starts/stops a previously set program
or cooking program.
ENCODER
The enoder knob rotates clockwise and anticlock-
wise, thus it increase or reduces the figure indicat-
ed on display. Remember to press the encoder for
confirmation also the figure will continue to flash.
CORE PROBE SECTION
Section where to introduce the core probe. The
cooking time cannot be set given that cooking will
end upon reaching the set inner temperature con-
trolled by the probe.
AUTOMATIC COOLING COOKING CHAMBER
To reduce automatically the cooking chamber tem-
perature press temperature button, acting on the
encoder reduce the temperature until desired, open
the door and press the encoder for confirmation.
The oven will immediately reduce the temperature.
AUTOMATIC CLEANING
The cleaning system is fully automatic: just select
the required program.
With the control panel in the OFF mode, press the
ENCODER knob.
The display will show CLN_01. Turn the ENCODER
knob until the required function appears.
Press the ENCODER knob again and start the program.
CLN_01: SHORT cleaning cycle (45 minutes).
CLN_02: MEDIUM cleaning cycle (56 minutes).
CLN_03: LONG cleaning cycle (65 minutes).
CHr___: detergent pump refill (3 minutes).
The detergent pump refill with the CHr program
must be carried out in the following cases:
upon first start up after installation.
every time the detergent in the container runs out.
after a long period of non-use.
IMPORTANT
ATTENTION: to guarantee the cleaning system’s per-
fect operation, make sure that the temperature of the
cooking chamber is between 90 °C and 140 °C be-
fore starting a cleaning program (CLN_01, CLN_02,
CLN_03).
Higher temperatures are not recommended.
The equipment is intended to clean professional
ovens. Any use other than that indicated must be
avoided, as this will be considered improper use
and, therefore, dangerous.
Before starting a cleaning cycle, make sure that
the water drain on the bottom of the cooking cham-
ber is clear, to prevent flooding the chamber.
Never open the cooking chamber when a cleaning
cycle is in progress. Chemical substances and hot
fumes may escape causing burns and corrosion.
At the end of every cleaning cycle, make sure that
no detergent residue is left in the cooking chamber.
Remove any residue from the cooking chamber
and rinse manually.
We recommend using the detergent approved by
the manufacturer.
The use of a non-approved detergent may damage
the cleaning system and may affect the integrity of
the cooking chamber, rendering the warranty null
and void.
8.1 WARNINGS AND ALARMS
All alarms are indicated by a buzzer. The buzzer
can be silenced by pressing a key.
Er1 CHAMBER PROBE ALARM
This is triggered if the chamber probe fails.
Everything is deactivated except for the light. The
cycle in progress is interrupted.
Er2 CORE PROBE ALARM
This is triggered if the core probe in the food being
cooked fails (where used). Everything is deactivated
except for the light. The cycle in progress is inter-
rupted.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 223256 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 223256 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info