741885
6
Zoom out
Zoom in
Previous page
1/56
Next page
COMBI STEAM OVENS NANO
PIECE KONWEKCYJNOPAROWE NANO
Item: 223307
223284
223260
223246
223222
223291
223277
223253
223239
223215
You should read this user manual carefully before
using the appliance
Bevor Sie das Gerät in Betrieb nehmen, sollten
Sie diese Gebrauchsanweisung aufmerksam lesen
Alvorens de apparatuur in gebruik te nemen dient
u deze gebruiksaanwijzing aandachtig te lezen
Przed uruchomieniem urządzenia należy koniecznie
dokładnie przeczytać niniejszą instrukcję obsługi
Lisez attentivement ce mode d’emploi avant d’utiliser
l’appareil .
Prima di utilizzare l’apparecchio in funzione leggere
attentamente le istruzioni per l’uso.
Citiţi cu atenţie prezentul manual de utilizare înainte
de folosirea aparatului
Внимательно прочитайте руководство пользователя
перед использованием прибора
User manual
Gebrauchsanweisung
Gebruiksaanwijzing
Instrukcja obsługi
Mode d’emploi
Istruzioni per l’utente
Instrucţiunile utilizatorului
Руководство по эксплуатации
Használati útmutató
Keep this manual with the appliance.
Zachowaj instrukcję urządzenia.
For indoor use only.
Do użytku wewnątrz pomieszczeń.
CONTENTS
1. SAFETY REGULATIONS ........................................... 4
2. PRELIMINARY OPERATIONS ...................................6
3. INSTALLATION AREA ..............................................6
4. PREPARING FOR INSTALLATION ............................ 7
5. ELECTRICAL CONNECTION .....................................7
6. WATER CONNECTION ............................................10
7. DRAINAGE CONNECTION ......................................11
8. STACKING OVENS..................................................11
9. SPECIFICATION ..................................................... 12
INSTRUCTIONS FOR THE USER
1. WARNING .............................................................. 13
2. USING FOR THE FIRST TIME .................................14
3. ORDINARY MAINTENANCE ................................... 15
4. EXTRAORDINARY MAINTENANCE ........................ 16
5. MAINTENANCE IN CASE OF BREAKAGE ..............17
6. COOKING ADVICE ..................................................18
7. MECHANICAL OVEN CONTROL PANEL ................. 19
8. DIGITAL OVEN CONTROL PANEL .......................... 20
9. TECHNICAL DATA .................................................. 23
10. DISCARDING & ENVIRONMENT ............................ 24
11. WARRANTY ............................................................ 24
3
EN
NOTE: all devices that require a steady connection to water mains (including this device) must be
connected to a water softener which removes calcium and magnesium compounds from the water.
The water softener must be used in line with the manufacturer’s recommendations included in
instruction manual.
If a water softener is not connected or is user and/or regenerated incorrectly, the dealer shall
not recognise any complaints related to repairs due to lime scale build-up in the device.
The following products are recommended to assure proper regeneration:
Salt tablets, 25 kg bag - code: 231265
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l Clark
degrees
Water softener
connection
over 24 over 40 over 4,2 over 28 Required
18 - 24 32 - 40 3,2 – 4,2 22 - 28 Required
12 - 18 19 – 32 2,1 – 3,2 13 - 22 Required
4 - 12 7 - 19 0,7 – 2,1 5 - 13 Required
under 4 under 7 under 0,7 under 5 Not required
5
EN
Do not use any extra devices that are not supplied along with the appliance.
Only connect the appliance to an electrical outlet with the voltage and frequency
mentioned on the appliance label.
Connect the power plug to an easily accessible electrical outlet so that in case of
emergency the appliance can be unplugged immediately. To completely switch off
the appliance pull the power plug out of the electrical outlet.
Always turn the appliance off before disconnecting the plug.
Never use accessories other than those recommended by the manufacturer. Failure
to do so could pose a safety risk to the user and could damage the appliance. Only
use original parts and accessories.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge.
This appliance must not be used by children under any circumstances.
Keep the appliance and its cord out of reach of children.
Always disconnect the appliance from the mains if it is left unattended or is not in
use, and before assembly, disassembly or cleaning.
Never leave the appliance unattended during use.
1.1 SPECIAL SAFETY REGULATIONS
Read this instructions booklet carefully before starting the installation and start-
up operations.
All installation, assembly, assistance and extraordinary maintenance shall be
carried out by qualified personnel and supplied with necessary professional
(authorizations by the manufacturer or retailer), in accordance with local
laws in effect where installation takes place regarding product and workplace
safety.
Incorrect installation, assistance, maintenance, cleaning, tampering or modifica-
tions can cause malfunction, damage and breakage.
The appliance must only be used for cooking or heating of foods in industrial kitchens.
Any other use is inappropriate and dangerous.
6
EN
1.2 WARRANTY
Any defect affecting the functionality of the ap-
pliance which becomes apparent within one year
after purchase will be repaired by free repair or re-
placement provided the appliance has been used
and maintained in accordance with the instructions
and has not been abused or misused in any way.
Your statutory rights are not affected. If the appli-
ance is claimed under warranty, state where and
when it was purchased and include proof of pur-
chase (e.g. receipt).
In line with our policy of continuous product devel-
opment we reserve the right to change the product,
packaging and documentation specifications with-
out notice.
1.3 DISCARDING & ENVIRONMENT
At the end of the life of the appliance, please dispose
of the appliance according to the regulations and
guidelines applicable at the time.
Throw packing materials like plastic and boxes in the
appropriate containers.
2. PRELIMINARY OPERATIONS
Once unpacked, ensure the oven is intact and does
not show signs of damage due to transport. A dam-
aged appliance must never be installed and com-
missioned; if in doubt, immediately contact the af-
ter-sales technical assistance or your own dealer.
In the case of damage or missing parts inform the
carrier and retailer/manufacturer immediately, in-
dicating the code (Art.) and serial number (Ser N°)
and attach a photo.
Check that the installation area is kept clear so that
doors, corridors and passageways are accessible.
3. INSTALLATION AREA
The appliance shall be installed in enclosed and well
ventilated areas (not outdoors).
The ambient temperature of the place of installa-
tion of the oven must be higher than +4°C.
Before positioning the appliance, check the overall
dimensions and the exact position of the electri-
cal, water and fumes exhaust connections, fumes
exhaust.
It is advised to place the oven under an extractor
hood or in such a way that hot fumes and odours
exit the oven via adequate ventilation to the outside.
The oven must be placed on a flat surface so that it
does not slip or turn over.
The installation area must be able to support the
weight of the appliance filled to the maximum.
See the information level on the back of the oven
for the gross weight.
Make sure that it is placed so that the door may be
fully opened.
Position it so that the back of the oven is easily ac-
cessible for maintenance, connection to the mains
sockets, and water.
The appliance is not meant to be fitted and a 5 cm
space must be left all round it.
Do not position other heat sources like, fryers or
hotplates, near the oven. If this is not possible at
least respect the following distances from machin-
ery: 50 cm from the sides and above the appliance
and 70 cm from behind.
Do not place the device near materials or contain-
ers of inflammable liquids (such as walls, furniture,
screens, gas canisters) as it can be a fire hazard. If
this is not possible, cover the inflammable parts
with fire and heatproof material and by checking
fire hazard regulations.
7
EN
4. PREPARING FOR INSTALLATION
Remove the outer packaging (wooden caging and/
or carton box) and dispose it in compliance with the
laws in force in the country of installation.
REMOVING PROTECTIVE FILM ETC.
All packaging must be fully removed, including the
protective film applied on the external and internal
walls.
Remove all information covering from the inside,
and take off all plastic packaging.
STAND ADJUSTMENT
Do not use the appliance without feet.
The adjustable feet are already screwed to the un-
derside of the oven.
If they are not used, this prevents airflow from
cooling the electric parts and outsides of the oven
which causes over-heating and damage to compo-
nents.
The oven will function correctly if placed level on
a flat surface by adjusting the feets accordingly and
using a spirit level. Screw or unscrew them as nec-
essary to adjust.
FITTING THE DRIP TRAY DRAIN
Fit the plastic clip and the white water pipe that is
inside the packaging. Check that the pipe is firmly
connected so that water can flow from the tray to
the drain (see image).
5. ELECTRICAL CONNECTION
WARNING: Main connections must be carried
out by a qualified and authorized technician ac-
cording to national, international and local laws
in the country where it is installed. Before mains
connection, ensure that the frequency (...V) and
voltage (...Hz) meet the requirements indicated
in the in the information tag on the back of the
appliance.
The electric system, as prescribed and specified
by the Standard in force, must be equipped with
an efficient ground. It is possible to guarantee the
electric safety of the appliance only in the presence
of Standard electric system.
For direct connection to the mains, it is necessary
to interpose a device between the equipment and
the same mains, sized for the load, that ensure its
disconnection. The contacts must have an opening
distance enabling the full disconnection, in condi-
tions of over-voltage category III, per compliance
with installation regulations.
This device also must be located in a place and in
a manner to be easily accessible at any moment by
the operator.
8
EN
5.1 CONNECTING THE CABLE
Loosen the screws fixing the left side of the oven
and extract it.
The oven must be connected to the electricity with
a rubber cable.
WARNING: the yellow/green voltage wires in the
earth cable must be 3 cm longer than the others.
The appliance has terminal strips such as those in
the diagram. To connect to the electricity, see the
label in the manual and stuck to the bottom of the
back of the device beside the information plate.
The appliance has terminal strips such as those in
the diagram. To connect to the electricity, see the
label in the manual and stuck to the bottom of the
back of the device beside the information plate.
Proceed as follows to connect the power supply
wire to the terminal board:
(A1) Loosen the tops of the cable gland and open
the bottom part of the back of the appliance by
loosening the screws.
(A2) Feed the new cable through the cable gland.
Connect the cable voltage to the terminal strips
following the connection diagram on the label
on the back of the appliance. Only connect what
is indicated inserting the copper bridge and the
electricity cable together under the screws, in
the tightening direction, so the cable and the
bridge are tightly fixed by tightening the screw.
The type of cable to be used is indicated on the la-
bel
for each connection and the voltage sections
in mm².
(A4) Close the bottom part of the back of the ap-
pliance by tightening the screws and fit the cable
by tightening the cable gland top.
A1
A3
A2
A4
9
EN
A1
A3
A2
A4
Erroneous connection could lead to overheating of the terminal board which could lead to blowout and elec-
tric shock.
Check that all the connections are tight before connecting the oven to the mains.
E = Yellow/Green: “EARTH” protection conductor.
N = Blue: neutral conductor.
L1, L2, L3 = Brown, Grey, Black: live conductors
Check there is no static discharge between live and earth. Check the limit switch continuity between the ex-
ternal casing and the earth wire of the mains. It is advised to use a multi tester to carry out these operations.
5.2 CABLE SUBSTITUTION
This must be carried out by a qualified authorized
technician. The earth wire must always be yellow
green.
WARNING: the yellow/green voltage wires in the
earth cable must be 3 cm longer than the others.
Proceed as follows to connect the power supply
wire to the terminal board:
(A1) Loosen the tops of the cable gland and open
the side part of the appliance by loosening the
screws.
(A3) Loosen the terminal screws and feed the cable
conductors through. Take out the old cable from
the cable gland.
(A2) Feed the new cable through the cable gland.
Connect the new cable’s conductors to the ter-
minal following the connection diagram on the
label at the lower part of the back of the appli-
ance. Only connect what is indicated inserting the
copper bridge and the electricity cable together
under the screws, in the tightening direction, so
the cable and the bridge are tightly fixed by tight-
ening the screw. The type of cable to be used is
indicated on the label for each connection and
the voltage sections in mm².
(A4) Close the side part of the appliance by tight-
ening the screws and fit the cable by tightening
the cable gland top.
10
EN
Check that all the connections are tight before con-
necting the oven to the mains.
WARNING: Erroneous connection could lead to
overheating of the terminal board which could
lead to blowout and electric shock.
Check there is no static discharge between live and
earth. Check the limit switch continuity between
the external casing and the earth wire of the mains.
It is advised to use a multi tester to carry out these
operations
5.3 EQUIPOTENTIAL CONNECTION
This connection shall be carried between the dif-
ferent appliances with the terminal marked by the
symbol: .
This terminal enables the connection of Yellow/
Green cable with a section between 2.5 and 10 mm².
The appliance shall be included in an equipotential
system whose efficiency shall be duly verified ac-
cording to the provisions of the laws in force.
6. WATER CONNECTION
Make sure the device is placed near a water con-
nection. Before connecting the device, allow enough
water through to remove any remnants in the piping
so that they did not get into the magnetic valves. It is
necessary to install a shut-off valve and mechanical
filter between the plumbing and the device.
On the back of the device, in the area marked with
a label, the convection oven has an input G 3/4” with
a filter. The inflowing water shall have a pressure
value comprised between 150 (1,5 bar) and 200 kPa
(2 bar) and a maximum temperature of 30°C. If the
inflow pressure value exceeds 200 kPa (2 bar),
a pressure reducer will have to be installed, cali-
brated at 200 kPa (2 bar).
6.1 WASHING WATER CONNECTION
A shut-off valve and a mechanical filter must be
placed between the mains water supply and the
oven. The rear of the oven has a G 3/4” inlet with
pipe.
ATTENTION: Before connecting the appliance to
the mains water supply, rinse with water to elimi-
nate any residue. To guarantee proper operation of
the cleaning system, the mains water supply pres-
sure must be a minimum of 200 kPa (2 bar) and the
temperature must not exceed 30°C. Lower water
pressure values may prevent the cleaning system
from working properly.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hendi 223256 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 223256 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info