Manual Hendi 222973 (page 8 of 30) (English, German, Dutch, Danish, French, Italian, Swedish, Norwegian)

741077

Zoom out

Zoom in

1/30

Dear Customer,

To guarantee the safety and correct working of the appliance,

please read the following instructions CAREFULLY before begin-

ning the installation.

IMPORTANT:

Make sure that the power supply has been disconnected before

performing the installation or electrical connection of the appliance.

Installation, electrical connections and settings must be carried

out by a qualified person in line with local regulations.

If these installation instructions are not followed the product may

be damaged.

For optimal performance, the appliance must be installed co-

rrectly (installation of the unit, ducts and air replacement inlets).

This extractor fan is designed for the ventilation of households or

similar premises. Do not use for any purpose other than that for

which it was designed.

This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental ca-

pabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved. Children shall

not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision.

The fan is to be installed so that the blades are more than 2,3 m

above the floor.

This extractor fan does not produce radio/television interference

(Directive 2004/108/EC).

Prior to piping installation, consult the municipal by-laws on air

outlets and request permission from the person responsible for

the building.

Precaution must be taken to avoid the backflow of gases into the

room from the open gas pipe or from other open-flame devices.

The room must have adequate ventilation if this appliance is used

simultaneously with other appliances that run on gas or other fuels.

Do not install the exhaust conduit (A, B) of the extractor fan to a

chimney flume, ventilation pipes, hot air ducts or ducts used to

evacuate fumes from appliances that run on gas or other fuels.

DO NOT install this product in areas with the follow characte-

ristics:

• Excess of oil or grease.

• Areas with corrosive, explosive or flammable liquids, gases or

vapours.

• Areas with temperatures higher than 60 °C or lower than -5 °C.

• Areas exposed to the environment (rain, sun, snow, etc.)

• Areas with possible obstacles that obstruct the access to the

fan.

The product and its parts must not be submerged in water or

other liquids.

The IP rating is only valid if the installation of the appliance com-

plies with what is indicated in this manual.

The manufacturer declines all responsibility for personal injury

or damage to animals or objects caused by inappropriate use of

the appliance according to the warnings for installation, use and

maintenance described in this instruction manual.

After finishing the installation these instructions should be given

to the owner/user of the appliance.

INSTALLATION:

Before starting the installation, check that the propeller is not de-

formed or damaged, that it can turn freely, and that no foreign

body is lodged inside the outer casing.

This type of tubular extractor is designed to work within any sec-

tion of the air exhaust duct (rigid or flexible) in either a horizontal

or a vertical position.

The appliance shall be installed according to the attached graphic

documentation (see fig. 1 and 2)

• Loosen the 2 screws (D) and lift the flanges (E). Take the casing

assembly (F) out of its housing.

• Place the bracket + openings (G) in the place where you want

to install the extractor (wall or ceiling) and mark the holes (H).

• Make four holes with a suitable drill bit and secure the bracket

using the plugs and screws included with the appliance.

Is recommended that you place the appliance at a distance equal

to or greater than one metre from the bend or the closest suction-

expulsion opening.

• Join the suction (A) and expulsion (B) conduits to the nozzles (I)

by flanges or resistant adhesive tape

It is important that the diameter of the tube should be equal to

the diameter of the openings to ensure efficient operation of the

appliance.

• Replace the casing (F) in its housing in such a way that the

air circulation direction indicated by the arrows (J) and the cable

outlet direction are as desired.

Close the flanges (E) and tighten the screws (D)

Whether the assembly is done with an individual exhaust tube

or with a direct outlet, air grilles must be installed that comply

with national safety requirements for preventingaccess to the fan

blades Make sure that there is no obstacle blocking the flow of air.

ELECTRICAL CONNECTION:

Make sure that the voltage (V) and frequency (Hz) of the power

supply correspond to the values indicated on the nameplate.

The appliance must be able to be disconnected from the mains

electricity supply after installation.

ENENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hendi 222973 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian as an attachment in your email.

The manual is 2,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hendi 222973 Manual

Product: