629813

Heidenhain CNC Pilot 4290 Manual

711
Zoom out
Zoom in
Previous page
1/725
Next page
HEIDENHAIN CNC PILOT 4290 711
Index
Sequential events ... 320
Serial interface ... 666
Service functions ... 647
Setting dimensions ... 622
Setting the feed per revolution ... 62
Setting up machine dimensions ... 78
Setting up the chucking table ... 74
Setup
DIN PLUS program head ... 136
Setup functions ... 75
TURN PLUS program head ... 393
Set-up parameters ... 583
Shaft machining (TURN PLUS)
Fundamentals ... 557
Preparing a machining
process ... 482
Shaft speed
Spindle speed override ... 87
Shaft speed with V constant
G922 ... 311
Sharing
Enabling password ... 656
Shared directories ... 668
Shift, activating tool lengths
G981 ... 310
Shifting the contour G121 ... 202
Side mill cutter ... 613
Side view (YZ) (simulation) ... 368
Simple contour repeat cycle G83 ... 234
Simple face roughing G82 ... 232
Simple tools
Programming ... 140
Setup ... 71
Simplified geometry
programming ... 120
Simulation
3-D view ... 382
Checking multi-channel
programs ... 386
Chucking equipment
depiction ... 364
Contour generation during
simulation ... 378
Contour Simulation ... 374
Dimensioning ... 375
Display ... 364
Errors and warnings ... 372
Front window ... 368
Line and trace display ... 367
Machining simulation ... 376
Motion simulation ... 380
Operating mode .. ... 362
Screen contents ... 363
Side view (YZ) ... 368
Surface window ... 368
Synchronous point analysis ... 388
Time calculation ... 387
Tool depiction ... 364
TURN PLUS control graphics ... 548
Zero point shifts ... 366
Zoom function ... 371
Single hole (TURN PLUS) ... 426
Single-block mode
Automatic operating mode ... 86
Simulation ... 363
Skip cycle ... 326
Skip level
Execution ... 326
Fundamentals ... 112
Sleeve monitoring G930 ... 310
Slide change key ... 66
Slide code
Conditional block run ... 326
Fundamentals ... 112
Slide display (display element) ... 97
Slide synchronization ... 282
General ... 282
Multi-slide programming ... 332
One-sided synchronization
G62 ... 284
Synchronization marking
G162 ... 285
Synchronous start of slides
G63 ... 285
Slot
DIN PLUS
Circular slot on front/rear face
G302/G303 ... 175
Circular slot on lateral surface
G312/G313 ... 182
Linear slot on front/rear face
G301 ... 175
Linear slot on lateral surface
G311 ... 182
TURN PLUS
Circular slot on front/rear
face ... 432
Circular slot on lateral
surface ... 444
Linear slot on front/rear
face ... 431
Linear slot on lateral
surface ... 443
Slot, linear
DIN PLUS
Front/rear face G301-Geo ... 175
Lateral surface G311-Geo ... 182
TURN PLUS
Front/rear face ... 431
Lateral surface ... 443
Software limit switch
Manual control ... 61
Reference run ... 58
Source block display (simulation) ... 369
Special machining tasks (SM) ... 532
Spindle
Spindle change key ... 66
Spindle condition ... 99
Spindle keys ... 65
Spindle override 100% G919 ... 307
Spindle speed ... 62
Spindle synchronization
G720 ... 286
With workpiece G98 ... 283
Spindle display (display element) ... 97
Spindle keys ... 65
Spindle point stop ... 62, 63
Spindle speed
Block speed monitoring off
G907 ... 306
Constant surface speed
Gx96 ... 195
Speed Gx97 ... 195
Speed limitation Gx26 ... 192
… 711 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Heidenhain CNC Pilot 4290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Heidenhain CNC Pilot 4290 in the language / languages: English as an attachment in your email.

The manual is 14,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Heidenhain CNC Pilot 4290

Heidenhain CNC Pilot 4290 User Manual - German - 729 pages

Heidenhain CNC Pilot 4290 User Manual - Dutch - 730 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info