665972
2
Zoom out
Zoom in
Previous page
1/12
Next page
“C”, LR14
“C”, LR14
Code Setting Switch
Kodierschalter
SLOGBD
HR
Sender Batterieinstallation
Der Sender wird durch eine 3 Volt
Lithium CR2032 Batterie betrieben,
welche im Lieferumfang enthalten
und bereits eingelegt ist.
Entfernen Sie lediglich die Schutz-
folie, welche seitlich aus dem Sender
herausschaut, so daß ein elektrischer
Kontakt hergestellt wird.
Um die Batterie zu wechseln,
entfernen Sie zunächst die Rückseite
des Senders durch vorsichtiges
Eindrücken des Riegels mit einem
kleinen, schmalen Schraubendreher.
Lösen Sie die Schraube der
Batteriehalterung und tauschen
Sie die alte Batterie aus.
Überprüfen Sie, ob die Batterie
gemäß der angegebenen Polarität
(+ = oben) richtig eingelegt ist.
Setzen Sie die Rück- und Vorder-
seite des Senders wieder
zusammen. Der Sender ist nun
betriebsbereit.
Empfänger Batterieinstallation
Schieben Sie die Batteriefach-
abdeckung auf der Rückseite nach
unten und legen Sie die Batterien
ein (nicht im Lieferumfang
enthalten) 2 x 1,5 Volt LR14 /
Baby. Beim Einlegen
bitte auf Polarität achten!
Schieben Sie die Batterie-
fachabdeckung des Empfängers
wieder ein. Der Empfänger ist
nun betriebsbereit.
Anschluss an eine vorhandene
Klingelanlage
Dieses Funkgong-Set ist auch
für den Anschluss an eine vor-
handene Klingelanlage geeignet.
Transmitter Battery Installation
The transmitter is operated by
a 3 Volt Lithium CR2032 battery,
which is included in delivery
and is pre-installed inside the
transmitter.
Just remove the protective foil
sticking out from the side of
transmitter, which will establish
the electrical contact.
To replace the battery first
remove the back cover of
transmitter by carefully pressing
the latch with a small, narrow
screwdriver.
Loosen the screw of the battery
bracket and replace the old battery.
Please check if the battery is
inserted correctly according to the
polarity (+ = up).
Reassemble the back and front
of the transmitter. The transmitter
is now ready for operation.
Receiver Battery Installation
Push down the battery cover on
back and insert batteries (not
included in delivery) 2 x 1,5 Volt
LR14 / Baby. Please mind the
polarity! Push the battery cover
of the receiver back into position.
The receiver is now ready for
operation.
Connection to an existing bell
system
This wireless chime set is also
suitable for connection to an
existing door bell system. The
Instalacija baterije oddajnika
Oddajnik poganja 3 voltna litijeva
baterija CR2032, ki je vsebovana v
obsegu dobave in že vložena.
Odstranite samo zaščitno folijo, ki
ob strani gleda ven iz oddajnika,
tako da se vzpostavi električni
kontakt. Za menjavanje baterije
najprej odstranite hrbtno stran
oddajnika, tako da zapah s
pomočjo ozkega izvijača previdno
vtisnete. Odvijte vijak držala za
baterijo in staro baterijo
zamenjajte. Prekontrolirajte, ali je
baterija v skladu z navedeno
polarizacijo (+ = zgoraj) pravilno
vstavljena. Hrbtno in sprednjo
stran oddajnika zopet sestavite.
Oddajnik je sedaj pripravljen za
uporabo.
Instalacija baterije sprejemnika
Pokrov predalčka za bateriji na
hrbtni strani potisnite navzdol in
vložite bateriji (nista vsebovani v
obsegu dobave) 2 x 1,5 voltna
LR14 / Baby. Pri vlaganju pazite
na polarizacijo! Pokrov predalčka
za bateriji sprejemnika zopet
potisnite noter. Sprejemnik je
sedaj pripravljen za uporabo.
Priključitev na razpoložljiv zvonec
Ta komplet z brezžičnim gongom je
primeren tudi za priključitev na
razpoložljiv zvonec. Brezžični
oddajnik pri tem dopolnjuje
obstoječe, ožičen gumb za zvonec.
Ugradnja baterija u odašiljač
Odašiljač pokreće 3-voltna litijeva
CR2032 baterija koja je obuhvaćena
isporukom i već je umetnuta.
Samo uklonite zaštitnu foliju koja
bočno strši iz odašiljača kako biste
uspostavili električni kontakt. Kako
biste zamijenili bateriju, najprije
opreznim utiskivanjem utora malim,
uskim odvijačem uklonite stražnju
stranu odašiljača.
Odvrnite vijak držača baterije i
zamijenite staru bateriju. Provjerite
je li baterija pravilno umetnuta u
skladu s navedenim polaritetom (+ =
gore). Ponovno sastavite stražnju i
prednju stranu odašiljača. Odašiljač
je sada spreman za rad.
Ugradnja baterija u prijemnik
Potisnite pokrov pretinca za
baterije na stražnjoj strani nadolje
i umetnite baterije (nisu
obuhvaćene isporukom) 2 x 1,5 V
AA LR14/Baby. Pri umetanju
pazite na polaritet! Ponovno
utisnite pokrov pretinca za
baterije na prijemniku. Prijemnik
je sada spreman za rad.
Priključivanje na postojeći sustav
zvona
Ovaj komplet bežičnoga signalnog
zvona također je prikladan za
priključivanje na postojeći sustav
zvona.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Heidemann 70292 - HX Loud at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Heidemann 70292 - HX Loud in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Heidemann 70292 - HX Loud

Heidemann 70292 - HX Loud User Manual - German, Dutch, French, Italian - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info