801910

Hayward SP 1080 series Auto skim Manual

6
Zoom out
Zoom in
Previous page
1/21
Next page
6
INSTRUCTIONS FOR INSTALLATION AND USE
HaywardAuto-Skim skimmers are designed for all sizes and all types of residential pools.
They are non-corrodible, and their robust structure makes them almost indestructible in all climates.
HaywardAuto-Skim skimmers have been present for many years on the global market, and they will satisfy all of your
quality requirements.
Please consult these instructions for dimensions and installation details.
LOCATION OF THE SKIMMERS
In order to obtain maximum effectiveness, install the skimmer(s) facing the prevailing wind to optimise recovery
of surface dirt. It is also recommended to install the outlet fittings facing the skimmer in order to push debris towards it.
Number of skimmers: generally one skimmer per 25 m2of pool area.
Rated maximum flow rate per skimmer: 7 m3per hour (for a 1½" outlet) - 10 m3per hour (for a 2" outlet).
Positioning: cemented at the tops of the pool sides (generally under the pool edge), as high as possible in the pool.
Water level: always at least half way up the opening of the skimmer in order to guarantee excellent hydraulic operation
of the filtration without any air being drawn in. It should be maintained at least 2 cm from the top of the opening in order
to obtain excellent skimming of the water in the pool.
INSTALLATION FOR ACONCRETE POOL
TheAuto-Skim SP1082 comes with two outlets (2" and 63 mm) for 63-mm pipes. It is necessary to use a reducing fitting
for the outlet to the inlet of the pump when 50-mm pipes are used.Aplug is provided for the 2" outlet when the 63-mm
outlet is used (punch-out membrane). Connect the overflow to the rear of the skimmer with a 50-mm pipe. Connect the
skimmer to the desired piping system and support it firmly in its final position. Cast about 10 cm
of construction concrete around the skimmer monolithically. Use a gasket as shown in Page 2. The ring for adjusting
the lid offers vertical adjustment of 38 mm in order to take up any misalignment between the top face of the skimmer and
the surrounding paving.
INSTALLATION FOR NON-WOODEN PANELS (SP1084 - SP1085)
1) Cut out and drill the wall panel to size (Page 3 for SP1084 and Page 4 for SP1085).
2) Put the gasket on the front portion of the skimmer. Ensure that the holes in the gasket are exactly in register with
the holes in skimmer. (Alittle adhesive will hold the gasket in place during the installation).
3) Place the skimmer with its gasket in the cutout in the wall panel and fasten together the elements of the resulting
assembly with two flat-head screws (in the centres of the top and of the bottom of the skimmer mouth.
4) If the pool is a liner pool, install the liner before going to point 5) below.
5) Fasten the second gasket and the face plate of the skimmer to the skimmer mouth by means of the 1" screws.
When the pool has a liner, drill the holes in the liner through the face plate, and then insert the screws (one by one).
The screws thus pass through: 1 - the face plate; 2 - the gasket; 3 - the liner; 4 - the panel; 5 - the gasket;
6 - into the skimmer mouth.
6) When the pool has a liner, cut out the liner around the inside of the face plate.
GB
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hayward SP 1080 series Auto skim at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hayward SP 1080 series Auto skim in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info