Manual Hayward Pool Vac series Navigator (page 5 of 24) (English, German, Dutch, French, Italian, Portuguese, Spanish)

801938

Zoom out

Zoom in

1/24

Remove the vacuum gauge from the hose and keep

it within easy reach. You will need it from time to

time to check the operation of the cleaner.

Step 8. Observe the cleaner in operation. The dis-

charge of water into the pool may affect the cleaner,

either at the hose on the surface or with the cleaner

itself at the bottom of the pool. If the pool’s dis-

charge can swivel, turn it so the flow of water does

not interfere with the movements of the cleaner.

Otherwise, ask your dealer to help find a solution.

Step 9. Check that the cleaner moves without stop-

ping too long at steps and other obstacles (vertical

walls, ladders). If it seems to you that the cleaner

is stuck, set the rear flap adjustment knob to I (see

figure 3).

Step 10. The cleaner climbs the vertical walls of

cement and fiberglass pools provided that they join

the pool bottom in a smooth curve (radius at least

30 cm). When the cleaner climbs a wall, It may

stop short of the top. If the cleaner seems not to

grip the wall, set the rear flap adjustment knob to

III (see figure 3).

If the cleaner reaches the water surface and takes

in air, set the rear flap adjustment knob to I (see

figure 3). If the cleaner still climbs too high, reduce

the suction power by 25 mm (1’’) until operation

becomes normal.

About 80% of pool residues are on the bottom, the

remaining 20 % on the walls, so the cleaner spends

more time cleaning the bottom than the walls.

Because of the shape of most sunken liner pools

(corners too sharp), the cleaner is confined to the

bottom (whatever the depth) and sloping walls. The

cleaner does not climb vertical liner walls.

Now that your cleaner is installed and working prop-

erly, enjoys your pool.

IMPORTANT RECOMMENDATIONS

1. Check regularly that the hose of the cleaner

is properly connected to the skimmer suction

port.

2. Disconnect the hose of the cleaner beforeback-

washing the filter. This is to ensure the flow of

water needed for effective back-washing.

3. Never coil the hose of the cleaner. The war-

ranty does not cover problems caused by

coiled hoses.

4. Warning: If massive chlorination is applied, it

is essential to remove the cleaner and its hose

from the pool until the chlorine level returns to

normal.

5. Always disconnect the main hoses from the

cleaner head when the latter is not in the pool.

6. Always carry and lift the cleaner by its handle,

never by the hose.

7. Remove the cleaner and its hose from the pool

before using the pool.

8. Check the vacuum regularly using the vacuum

gauge. Too much or too little suction is harmful.

9. Keep the back grate clean and free of debris by

regular brushing.

MAINTENANCE TIPS

The cleaner has a «removable bottom». The pur-

pose of this feature is readier access to the turbine/

suction chamber unit for servicing or cleaning.

Should the cleaner stop or slow down too much

because of the build-up of residues in the neck or

inside the device, you can reach the turbine/suction

chamber unit (see figure 11).

DISCLAIMER

1. Ageing, sunlight, and chemical treatments

damage the liner.

2. The liner may be weakened and become brittle.

3. The pool’s installation and environment may

also affect the liner.

4. When you install your cleaner, you take com-

plete responsibility for the condition of your pool

and its environment.

Important: Remove the AEV096 vacuum gauge

after adjusting the cleaner. It is not designed to

be left in the water and is not covered by the

warranty.

Remark: Bear these points in mind when install-

ing your cleaner.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hayward Pool Vac series Navigator in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hayward Pool Vac series Navigator Manual

Product: