801942
25
Zoom out
Zoom in
Previous page
1/136
Next page
Only use spare parts supplied by Hayward brands®
Page 7 on 16AquaRite® Pro Touch
EN
Connecting inputs:
Name Description Terminals Type of input/output
FL1 Flow switch A - C Dry contact
Cover Closed cover detection A - D Dry contact
pH Peristaltic pump E - F 230 V voltage output
°C/°F Temperature probe (not supplied) G - H - I Red, Yellow, Black
3d. Electrical installation and wiring
Connect the AquaRite® Pro Touch to a permanent power outlet.
: This circuit must be protected by a residual current device
(RCD) (residual current: 30 mA max.)
and a 16A time-delay circuit-breaker. Remove the white lid by unscrewing
the 6 screws using a screwdriver.
O
R
P
Rx probe
p
H
pH probe
Peristaltic
pump
3c. Installation of pH and ORP probes, and acid dosing pump
The pH and ORP probes are «wet» packed and protected by a plastic cap. The probes must always remain
wet. If the probes are allowed to dry, they will be permanently unusable (not covered by the warranty) and
the pH-ORP test kit will be ineffective.
Remove the pH and ORP probes from their plastic protective caps and set the caps aside for later use
(wintering). Insert the probes into the double probe holder and tighten to ensure they are watertight. Connect
the probe holder to the valves screwed onto the saddle clamps and tighten by hand only. Check that the
probes are watertight at startup. Seal with Teflon, if required.
After installation, check that the probes are constantly in contact with the water in the pool. When the filtration
pump is not running (even for long periods), the water remaining in the chamber may be sufficient to protect
the probes.
The product (acid, etc.) injection device must be installed last on the water return line, after any equipment
(heater, cell, etc.). A hole should previously have been drilled in the pipe to allow the treatment product to
pass through. Install the saddle clamp and screw the injection valve into the saddle clamp using the adapter
provided. Seal with Teflon.
Use the transparent PVC hose for suction (between the acid tank and the peristaltic pump) and the semi-
rigid white polyethylene tube for injection (between the peristaltic pump and the injection valve).
For the ORP option, install the ORP card in the RX slot on the motherboard.
pH
A
B
C
D
E
F
Détecteur
de débit
Closed cover
detection
ORP chip
(Rx) pH Chip
(pH) pH
probe
ORP
probe
Flow
switch
Peristaltic
pump
G
H
I
Temperature
probe
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hayward AquaRite Pro Touch Salt Chlorinator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hayward AquaRite Pro Touch Salt Chlorinator in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info