624009
8
Zoom out
Zoom in
Previous page
1/20
Next page
6
Guided Tour - Model LH1000 Rear Panel
1. AC Voltage selection switchThis switch is used to set the LH Series operation voltage. Be sure to check that the
switch is set correctly for your country.
2. EFFECTS SEND jack - Use this 1/4” unbalanced jack to send low impedance (100 ohm) signal from the Model LH1000
to a professional outboard effects processor such as a reverb, echo, chorus, flanger, or harmonizer device. Output level
isapproximately0dBto+4dBandispost-EQandpost-LimiterbutunaffectedbythesettingoftheVOLUMEcontrol.
You can also use the Effect Send jack to route signal to an external mixing console or amplifier with an input sensitivity
of +4 dB.
3. EFFECTS RETURN jack - Use this 1/4” unbalanced jack to return low impedance (600 ohm) signals to the Model
LH1000 from a professional outboard effects processor.
4. Fan - The fan provides vital cooling to your Model LH500 and LH1000. Make sure that it is kept free of all obstructions
and that cool, fresh air is accessible at all times. Also, try to ensure that the Model LH1000 is used in a dust-free
environment.
5. SPEAKER OUTPUT A - Connect any 4, 8, or 16 ohm bass cabinet(s) to these standard unbalanced 1/4” jacks. WARNING:
Because of the high power levels and low frequency content of the signal generated by the Model LH1000, use only
appropriately rated speaker cabinets (at least 600 watts at 4 ohms) that are specifically designed for bass instruments.
We recommend that Hartke amplifiers be used with Hartke bass cabinets, although other brands of speakers can be
used.
6. BRIDGE output connector - Connect a Speakon connector cable here when operating in Bridge mode.
7. SPEAKER OUTPUT B - Connect any 4, 8, or 16 ohm bass cabinet(s) to these standard unbalanced 1/4” jacks. WARNING:
Because of the high power levels and low frequency content of the signal generated by the Model LH1000, use only
appropriately rated speaker cabinets (at least 600 watts at 4 ohms) that are specifically designed for bass instruments.
We recommend that Hartke amplifiers be used with Hartke bass cabinets, although other brands of speakers can be
used.
8. BRIDGE switch – Used to set the LH1000 to operate in Dual Parallel or Bridge modes.
9. AC input - Connect the supplied standard 3-pin “IEC” plug here.
10. Fuse sled - This contains a fuse holder for your Model LH1000. Make sure the voltage rating is correctly set before
powering up the amplifier! Fuse ratings are 15 amp for115 vac and 7.5 amp for 230 vac.
2
1
3
7
10 8
4 5 6
9
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hartke LH500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hartke LH500 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info