769912
11
Zoom out
Zoom in
Previous page
1/14
Next page
11
SB 16 Programming the Soundbar to
Respond to Your TV Remote
Programming the Soundbar to Respond
to Your TV Remote
You can program the soundbar so it will respond to your TV remote’s power off, mute,
volume up, volume down and source commands. This programming lets you control
your whole home theater system with a single remote. Before beginning to program
the soundbar, have your TV remote in hand. We recommend sitting down in front of the
soundbar.
NOTE: Some steps will time out, so read through this entire procedure before you begin.
Have the remote handy. When you start the remote programming after step 4, be ready
to aim the TV remote at the front of the soundbar from about 300mm – 900mm (about
12 – 36 inches) away.
NOTE: If at any time the Surround and Source buttons both stop flashing, and the
soundbar returns to the power-on state, the programming operation has failed. In this
case, restart at step 2.
To program the power off, surround, volume down, volume up or source command:
1. Ensure that the soundbar is on.
2. Simultaneously press and hold the soundbar’s Power and Source buttons until the
visible Surround button flashes blue (the Power and Source buttons also flash but are
covered by your fingers). If the buttons do not flash after three seconds, release the
buttons and try again.
3. You now have 20 seconds to momentarily press the soundbar button that you want
to program (Power, Surround, Volume Down, Volume Up, Source), or the programming
operation will fail and you must restart at step 2. When you are successful, the
soundbar Power button light will turn off.
4. You now have 5 seconds to aim the TV remote at the front of the soundbar and slowly
and repeatedly press and release the corresponding button on the remote until the
Surround and Source buttons on the soundbar flash and then, after a few seconds,
return to constant illumination. This indicates that the programming operation has
been successful. Otherwise you must restart at step 2.
To program the Mute command: Repeat steps 1 and 2. At step 3, press and hold
the soundbar’s Power button until the Surround and Source buttons switch to constant
illumination. Then proceed to step 4.
To erase all remote programming: Ensure that the soundbar is on, then simultaneously
press and hold the soundbar’s Surround Mode and Volume Up buttons until the lights in
all the buttons flash.
TV Remote
Hold down both buttons until the
Power, Surround and Source
buttons indicators flash
Momentarily press the button
you want to program
300mm
(12")
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon SB 16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon SB 16 in the language / languages: English as an attachment in your email.

The manual is 1.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info