599846
3
Zoom out
Zoom in
Previous page
1/4
Next page
ASSEMBLY 3
ASSEMBLY
Assembly
1. If you will be placing the HTFS 2 stands
on a hard surface, such as a wood or
tile floor, attach four of the supplied
self-adhesive rubber pads to the
underside of the base in the recesses
as indicated in the drawing.
Place rubber pads or floor spikes here
2. If you will be using the HTFS 2 stands
on a carpeted surface, screw four of the
supplied floor spikes into the base using
the threaded inserts in the recesses as
shown in the drawing.
3. Following the instructions on pages 9
through 12 of the owner’s manual
provided with your HKTS system, thread
the appropriate speaker cable through
the hole in the center of the base, being
careful to avoid the two screw holes.
Then feed the cable through the length
of the column from the bottom until it
comes out the top.
4. Attach the column to the base using two
of the supplied screws.
5. Thread the speaker cable through
the hole in the center of the mounting
plate, being careful to avoid the three
screw holes.
6. Attach the mounting plate to the top of
the column using two of the supplied
screws. The mounting plate tab with the
third screw hole should sit on the higher
rim of the column.
Attaching the Speaker
to the Stand
1. Unscrew the bolt that attaches the black
shelf stand to the bottom of the speaker.
Store the stand in a safe place in case it
is needed for a future installation. The bolt
will be used to attach the speaker to the
floor stand mounting plate.
2. Insert the speaker wires into the terminals
on the bottom of the speaker, being care-
ful to observe the correct polarity.
3. Place the speaker on top of the mounting
plate with the remaining screw hole lined
up with the threaded insert on the bottom
of the speaker.
4. Insert the bolt that was used for the shelf
stand up through the remaining screw
hole and into the speaker.
Repeat the assembly and speaker attach-
ment processes for each floor stand in your
system, and adjust the final speaker place-
ment as indicated in the owner’s manual
supplied with the speakers. You are now
ready to enjoy your home theater system!
Remove
Stand
15mm
or 1/2"
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HTFS 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HTFS 2 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info