456575
13
Zoom out
Zoom in
Previous page
1/30
Next page
12
12 13
ENGLISH
If youre not running the speaker wire through the wall, insert it through the wall 5.
portion of the wall-mount bracket, as shown in the illustration below.
Pass the speaker wire through the speaker portion of the wall mount, as shown in 6.
the illustration below.
Bring Wire in
through Here
Bring Wire cut
through Here
If you have not already removed the speaker’s base, do so by pulling it straight off 7.
the speaker, as shown in the illustration below. Apply even pressure to both sides
of the base, and it should slide off smoothly.
Apply Pressure Evenly to
Both Sides of Base
Lift Base
Straight off
Speaker
CAUTION: Before making speaker connections, ensure that the receiver is
turned off and the receiver’s AC cord is unplugged from the receiver and the
AC outlet.
Connect the speaker wire to the speaker terminals, as shown in the 8. illustration
below:
Press down on the top of the terminal to open the connection hole.a)
Insert the wire’s bare end all the way into the hole.b)
Release the terminal to secure the wire. c)
Insert the conductor with the colored band into the speaker’s red ( + ) terminal. Insert
the other conductor into the speaker’s black ( – ) terminal.
+
A. Push Down on Cap
to Open Hole
B. Insert Base Wire into
Open Hole
C. Release Cap to Secure
Wire
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the
other terminal. Touching wires can cause a short circuit that can damage the receiver.
Slide the speaker portion of the wall mount onto the speaker, as shown in the 9.
illustration below. Fit the grooves of the mount onto the rails in the speaker.
Apply even pressure on both sides of the mount, and it should slide straight onto
the speaker.
Push the mount all the way onto the speaker until it snaps into place.
Pull any slack speaker wire back through the mount as you slide the mount onto
the speaker.
Fit Bracket Grooves
onto Speaker Rails
Push Down Evenly
on Both Sides of Bracket
Slide the speaker onto the mount’s wall section, as shown in the 10. illustration
below. Pull any slack speaker wire back through the mount’s wall section.
Slide Speaker
onto Wall Mount
Fit the metal stop plate into the recess on the bottom of the wall mount with 11.
the pad facing the mount. Fasten the stop plate to the mount using two of the
supplied screws. The stop plate will prevent the speaker from detaching from the
bracket and will help hold the speaker in position as you rotate it on the mount.
Stop Plate
Supplied Screws
Wall-Mounting the HS 210 Satellite Speakers
Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker.
Store the stand and bolt in a safe place in case you need them for a future installation.
Remove
Stand
(M6-1.25P
or 1.4"-20)
15 mm
Wall Plate
Mount the wall-bracket attachment plate on the wall.
If possible, position the speakers so that the mounting screws (not included; use
size #8) may be installed directly into a wooden wall stud. If that is not possible, use
optional wall anchors that are rated to support at least twenty-five pounds.
The customer is responsible for proper selection and use of mounting
hardware, available through hardware stores, to wall-mount the speakers
properly and safely.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HS 210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HS 210 in the language / languages: English as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon HS 210

Harman Kardon HS 210 User Manual - German - 30 pages

Harman Kardon HS 210 User Manual - Dutch - 30 pages

Harman Kardon HS 210 User Manual - French - 30 pages

Harman Kardon HS 210 User Manual - Italian - 30 pages

Harman Kardon HS 210 User Manual - Spanish - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info