534545
3
Zoom out
Zoom in
Previous page
1/10
Next page
HKTS 5
3
HKTS 160SUB Rear-Panel Connections
Crossover control: This knob adjusts the subwoofer's cutoff between 50Hz and 150Hz.
The higher you set the Crossover control, the higher in frequency the subwoofer will
operate and the more its bass will "overlap" that of the system's other speakers. This
adjustment helps achieve a smooth transition of bass frequencies between the subwoofer
and the system's other speakers for a variety of different rooms and subwoofer locations.
NOTE: If you have connected the subwoofer to a receiver/processor with a low-pass
filtered LFE output, set the subwoofer's Crossover control to the 150Hz positon (fully
clockwise).
Phase switch: The Phase switch determines whether the HKTS 160SUB’s piston-like
action moves in and out in phase with the satellite speakers. If the subwoofer were
to play out of phase with the satellite speakers, the sound waves produced by the
subwoofer could be canceled out, reducing bass performance and sonic impact. This
phenomenon depends in part on the relative placement of all the speakers in the room.
In most cases the Phase switch should be left in the "NORMAL" position. However, it
does no harm to experiment, and you can leave the Phase switch in the position that
maximizes bass response and impact.
Power On Mode switch: If this switch is set in the"AUTO" position and the Power switch
is set to "ON", the HKTS 160SUB will automatically turn itself on when it receives an
audio signal and will enter the standby mode once no audio signal has been received for
about 15 minutes. When this switch is set in the "ON" position, the HKTS 160SUB will
remain on whether or not it is receiving an audio signal. An LED on the HKTS 160SUB’s
top panel indicates whether the subwoofer is in the on or standby state:
When the LED glows white, the HKTS 160SUB is turned on.
When the LED is not illuminated, the HKTS 160SUB is in standby mode.
When the Power switch is set to "OFF", the LED will not be illuminated, no matter what
setting the Power On Mode switch is in.
Subwoofer Level control: Use this control to adjust the HKTS 160SUB’s volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Line-Level In/LFE connector : Connect the subwoofer output of your receiver or preamp/
processor to this jack. The signal from this connector passes through the subwoofer's
internal low-pass crossover.
Power switch: Set this switch in the "ON" position to turn the HKTS 160SUB on. The
subwoofer will then either be on or in standby mode, depending on the setting of the
Power On Mode switch.
Power cord (non-detachable): After you have made and verified all subwoofer and
speaker connections described in this manual, plug this cord into an active, unswitched
electrical outlet for proper operation of the HKTS 160SUB. DO NOT plug this cord into the
accessory outlets found in some audio components.
HKTS 160SUB Rear-Panel Connections
Crossover control
Phase switch
Power On Mode switch
Subwoofer Level control
Line-Level LFE connector
Power switch
Power cord
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HKTS 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HKTS 5 in the language / languages: English as an attachment in your email.

The manual is 3,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon HKTS 5

Harman Kardon HKTS 5 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info