769907

Harman Kardon HKTS 210 SUB Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
3
HKTS 210 SUB/HKTS 200 SUB Subwoofer Rear-Panel Controls
and Placing the Subwoofer
Phase switch: This switch determines whether the subwoofer transducer’s piston-like
action moves in and out in phase with the satellite speakers. If the subwoofer were to
play out of phase with the satellite speakers, the sound waves from the satellites could
cancel out some of the subwoofer’s sound waves, reducing bass performance and sonic
impact. This phenomenon depends in part on the placement of all the speakers in the
room. In most cases, the Phase switch should be left in the “Normal” position. However,
it does no harm to experiment, and you can leave the Phase switch in the position that
maximizes bass response and impact.
Bass Boost switch: Set this switch to “On” to enhance the subwoofer’s low-frequency
performance. Set this switch to “Off” for normal low-frequency performance.
Power On Mode switch: When this switch is set in the “Auto” position and when the
Power switch is set to “On,” the subwoofer will automatically turn itself on when it
receives an audio signal and will enter the standby mode after it has received no audio
signal for about 15 minutes. When this switch is set in the “On” position, the subwoofer
will remain on whether or not it is receiving an audio signal. An LED on the subwoofer’s
top panel indicates whether the subwoofer is in the on or standby state:
• When the LED glows white, the subwoofer is turned on.
• When the LED is not illuminated, the subwoofer is in the standby mode. When the
Power switch is set to “Off,” the LED will not be illuminated, no matter what setting
the Power On Mode switch is in.
Subwoofer Level control: Use this control to adjust the subwoofer’s volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Input Mode switch (HKTS 210 SUB only): When this switch is in the “Normal” setting,
the input signal from the Line-Level L/R In connectors is active. When this switch is in
the “LFE” setting, the input signal from the Line-Level LFE In connector is active.
External Trigger Input connector: Use the mini plug of the supplied combination LFE
and trigger cable to connect the External Trigger Input connector to the trigger output
of another compatible component. Whenever the subwoofer detects a trigger signal
between 3V and 30V (AC or DC), its amplifier will turn on. The amplifier will turn off after
the trigger signal ceases, even when the Power On Mode switch is in the “Auto” position.
Line-Level LFE In connector: The signal from this connector bypasses the subwoofer’s
internal low-pass crossover. When you’re connecting the subwoofer to the dedicated
subwoofer output of a receiver/processor that has its own low-pass crossover network,
use the Line-Level LFE In connector. HKTS 210 SUB only: You must also set the
subwoofer’s Input Mode switch in the “LFE” position.
Line-Level L/R In connectors: The signals from these connectors pass through the
subwoofer’s internal low-pass crossover. When you’re connecting the subwoofer to the
preamp or subwoofer outputs of a receiver/processor that does not have its own low-
pass crossover network, use both Line-Level L/R In connectors. HKTS 210 SUB only:
You must also set the Input Mode switch in the “Normal” position. If your receiver/
processor has only one subwoofer output, you can use either the L or R connector.
Power switch: Set this switch in the “On” position to turn the subwoofer on. The
subwoofer will then be either on or in the standby mode, depending on the setting of the
Power On Mode switch.
Power Cord (non-detachable): After you have made and verified all the connections
described in this manual, plug this cord into an active, unswitched electrical outlet for
proper operation of the subwoofer. DO NOT plug this cord into the accessory outlets
found in some audio components.
Placing the Subwoofer
The performance of a subwoofer is directly related to its placement in the listening room
and its physical position relative to the other speakers in the system.
While it is true that in general our ears do not hear directional sounds at the low
frequencies where subwoofers operate, when installing a subwoofer within the limited
confines of a room, the reflections, standing waves and absorptions generated within
the room will strongly influence the performance of any subwoofer system. As a result,
the specific location of the subwoofer in the room does become important to the amount
and quality of bass that is produced.
For example, placing the subwoofer next to a wall generally will increase the amount of
bass in the room; placing it in a corner (1) generally will maximize amount of bass in the
room. However, corner placement can also increase the destructive effect of standing
waves on bass performance. This effect can vary depending on the listening position –
some listening positions may yield very good results while others may have far too much
(or too little) bass at certain frequencies.
In many rooms, placing the subwoofer along the same plane as the left and right
speakers (2) can produce the best integration between the sound of the subwoofer and
that of the left and right speakers. In some rooms, the best performance could even
result from placing the subwoofer behind the listening position (3).
We strongly recommend that you experiment with placement before choosing a final
location for your subwoofer. One way you can determine the best location for the
subwoofer is by temporarily placing it in the listening position and playing music with
strong bass content. Move around to various locations in the room while the system
is playing (putting your ears where the subwoofer would be placed), and listen until
you find the location where the bass performance is best. Place the subwoofer in that
location.
3.
2.
TV
Front Left
Speaker
Surround Left
Speaker
Surround Right
Speaker
Front Right
Speaker
Center
Speaker
1.
3


Need help? Post your question in this forum.

Forumrules
1

Forum

harman-kardon-hkts-210-sub

Reset search

  • Kan U mij deze handleiding in de nederlandse taal mailen aub.
    georges.dessers@outlook.com Submitted on 1-8-2023 at 11:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HKTS 210 SUB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HKTS 210 SUB in the language / languages: English as an attachment in your email.

The manual is 0.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info