14 OPERATION
OPERATION
Basic Operation
Once you have completed the setup and configuration of
your new receiver, it is simple to operate and enjoy.
The
following instructions will provide the steps needed
to
enjoy the HK 3380:
• Install the two supplied AAA batteries in the remote
as shown. Be certain to observe the (+) and (–)
polarity indicators shown in the bottom of the
battery compartment.
•You may begin a listening session by pressing the
System Power Control 1 on the front panel or the
Main Power On Button å on the remote.The
Power Indicator 2 will turn red, then blue. This will
turn the unit on and return it to the input source that
was last used. The unit may also be turned on from
Standby by pressing any of the
Source Selector
buttons on the front panel 68)!#$
or remote ç.
To turn the unit off at the end of a listening session,
simply press the
System Power Control 1 on the
front panel or the
Main Power Off Button ∫ on the
remote.This places the unit in the Standby mode, and
the
Power Indicator 2 will turn amber to remind
you that the unit is ready for operation when a power
command is received from the remote.
When the remote is used to turn the unit “off” it is
actually placing the system in a Standby mode, as
indicated by the amber color of the
Power
Indicator
2.
•To dim the brightness of the
Information Display
Û, press the Dimmer Button ^˙.The first
press will dim the lights to half normal. The
Power
Indicator
2 will remain lit, but the light inside the
Volume Control Ú will go out. A second press will
turn the display completely off, but the
Power
Indicator
2 will remain lit to remind you that the
unit is on. Press the
Dimmer Button ^˙ again
to restore the display to normal brightness.
Source Selection
•To select a source at any time, press any of the
Source Selector buttons on the remote ç or
front panel
68)!#$.
• When a video source is selected, if you have
connected a video device to the video input jack for
that source, and if you have connected the
Video
Monitor Output
· to the composite video input of
your TV or video display, you will be able to enjoy
video programs from a broadcast, cable or satellite
television system; a VCR or hard-disk video recorder;
a DVD player; or any other video device with analog
line-level audio outputs and a composite video output.
NOTE: Although the HK 3380 is an audio/video
receiver, it is not a surround sound receiver.Audio will be
played in two-channel stereo or monaural, depending on
how the program material is encoded, and you will not
be able to hear any additional channels that may be
encoded in your source materials.You will not be able
to make any digital audio connections through the
HK 3380.The HK 3380 is designed to provide video
entertainment in a small system application that includes
devices such as a TV, VCR or DVD player located in a
bedroom, office or spare room, or as part of a multiroom
system when used with a multiroom controller.
• During a listening session you may wish to adjust the
Bass Ó, Treble Ô and Balance Ò controls to
suit your listening tastes.
• Adjust the volume to a comfortable level using the
front-panel
Volume Control Ú or remote Master
Volume Up/Down
π buttons.The volume level is
displayed as a negative number of decibels (dB) in the
Main Information Display B.The volume level is
relative to a maximum volume level that has been
assigned the value of 0dB. It is important that you
make sure never to exceed this maximum volume
level (0dB) at any time, in order to avoid possible
damage to your loudspeakers due to “clipping”, a type
of distortion that is not audible to the human ear until
it is severe enough to permanently damage most
loudspeakers. It is also possible, depending upon the
program material, for clipping to occur at volumes
below the maximum volume level.
•To temporarily silence all speaker outputs, press the
Mute Button ®4. This will cut the output to all
speakers, but it will not affect any recording or dub-
bing that may be in progress.When the system is
muted, the
Mute Indicator K will flash in the
Information Display Û and MUTE will flash in
the
Main Information Display B. Press the Mute
Button
®4 again to return to normal operation.
•For private listening, plug the 1/4" stereo phone plug
from a pair of stereo headphones into the front-panel
Headphone Jack 3.
• One or two separate sets of speakers may be
connected to the HK 3380. To listen to one of
the speaker sets, press the
Speaker Selectors
57√∑ corresponding to the desired speakers.
The active speakers will be indicated by the
Speaker
Indicators
A. Both speakers may be turned off for
private headphone listening.
•To program the HK 3380 for automatic turnoff, press
the
Sleep Button *©. Each press of the button
will increase the time before shutdown, displayed by
the
Sleep Timer C, in the following sequence:
The sleep time will be displayed in the
Information
Display
Û and it will count down until the time
has elapsed.
When the programmed time has elapsed, the unit will
automatically turn off. The
Information Display Û will
dim to one-half brightness when the Sleep function is
programmed. To cancel the Sleep function, press the
Sleep Button *© until the Sleep Timer C num-
bers disappear and the
Information Display Û shows
the current source. Pressing any control button while the
Sleep control is activated will momentarily return the
Information Display Û to full brightness for increased
legibility without interrupting the Sleep function.
Tuner Operation
The HK 3380’s tuner is capable of tuning AM, FM and
FM Stereo broadcast stations. Stations may be tuned
manually, or they may be stored as favorite station
presets and recalled from a 30-position memory.
Station Selection
1. Press the FM/AM Selector &ç to select the
tuner as an input.
2. Press these buttons again at any time to switch
between AM and FM.
3. To select stations, press the
Tuning Button 9Ü to
advance one frequency increment at a time, or press
and hold it, and the tuner will search for the next highest-
or lowest-frequency station that has an acceptable sig-
nal. To tune to the next station, press and hold the button
again. When the
Tuned Indicator I lights, the station
is properly tuned and should be heard with clarity.
4. Stations may also be tuned directly by pressing the
Direct Button ∆, and then pressing the Numeric
Keys
˚ that correspond to the station’s frequency.
The desired station will automatically be tuned.
NOTE: When the FM reception of a station is weak,
audio quality will be increased by switching to Mono
mode by pressing the
FM Mode Button (ß until
the
Stereo Indicator H goes out.
