502536
11
Zoom out
Zoom in
Previous page
1/16
Next page
11
HD 990
Programmed Play Operation
Programmed Play
The HD 990’s advanced programming capability enables you to select certain tracks, to
preset the order in which these tracks play, and to clear specific programmed tracks after
the program was made.
Programmed play allows you to program up to 32 tracks into the HD 990’s memory. To
begin programming the CD player, make sure that the unit is in Stop mode, then press
the
Program
button d. The
Program
indicator will light in the
Information Display
1, the number 001 will blink below the Program indicator, showing the track number
selected, and PROG-01: 001 will appear in the Information Display, replacing the
track time. This indicates that you are about to program the first track.
You may now begin to enter the tracks in the order in which you wish to have them
play. To select a track on the disc, press the
Numeric
buttons c corresponding to the
desired track. Be certain to enter the second and/or third number of two- or three-digit
numbers within two seconds after the first number was entered. You may also use the
Skip
buttons 78h to select a track. When the track is selected, press the
Program
button d. Note that the program-step indication on the right side of the
Information
Display
will change to PROG-02: 001.
You may now select another track for the next program step, following the instructions
shown above. When the track is selected, press the
Program
button d again. Repeat
this procedure for each program step until you have completed the desired programming.
Press the
Stop
button 6k once to complete a program sequence, or press
Play
4jto begin immediate play of a program sequence. If the maximum of 99 program
steps is reached, the program-step indication at the right side of the Information Display
will go out, and the disc and track that have been programmed as the first program step
will be shown.
Once a program list has been entered, press the
Play
button 4jto begin listening
to the sequence. After the entire program has been played, the CD player will stop. As
long as the
Stop
button 6khas not been pressed twice and the
Program
indicator
remains lit, you may repeat the programmed-play sequence again by pressing the
Play
button 4j.
Editing a Program
A program can be edited even after it was completed by pressing the
Stop
button 6 k
once: Each time you press the
Program
button d the track number and program step
number will be displayed in the programmed order, but with steady track numbers (not
blinking) in contrast to the programming mode. As soon as the track number starts
blinking (this will take 1 second), the appropriate program step number shown at the left
side is not programmed yet; now you can change the track number with the
Skip
buttons
78hor the
Numeric
buttons c as described above and add it to the program
list by pressing the Program button d.
Pressing the
Stop
button 6k twice will return to normal mode and the
Program
indicator will go out, but the program will stay in memory and can be recalled easily by
pressing the
Program
button. But pressing the
Clear
button e (see below) or opening
the disc drawer by pressing
Open/Close
3p, will erase the program information
from the unit’s memory.
Checking Program Contents
To check the contents of a program while the unit is stopped at first note that the
Program
indicator is lit (otherwise press
Program
) and the program step indication PROG-01:
is not lit (otherwise press
Stop
once). Each time the
Check
button o is pressed now,
the Information Display will step through each of the programmed tracks. To cancel the
check mode press the
Stop
button twice.
Clearing Programs
To clear a single track from the program list, press the
Program
button d until the
track to be deleted from the program sequence appears in the
Information Display
1.
When the track number appears, press the
Clear button
e once, the track selected
will be deleted and the track number will be replaced by the next programmed one. Now
you can delete that track too with the Clear button or press the
Stop
button 6k and
again the
Program
d button to select lower track numbers to be deleted.
When the unit is stopped and the program step indication PROG-01: 001 is not
lit (otherwise press
Stop
once), but the
Program
indicator is still lit (otherwise press
Program
d) you may clear the entire contents of a program by pressing the
Clear
button e.
Important Note
: When you’ve pressed the
Program
button d (once or several times)
and the track number on the right starts blinking, the appropriate program step number
(e.g. PROG-02:008) shown at the left display side is not programmed yet. Do
not continue to press the Program button now, otherwise the track selected will be
memorized too. If you´re in doubt, press
Stop
button 6k and start the procedure
again with
Program
d.
Important Note
: Tracks programmed as described above can be played repeatedly too.
When you press
Repeat
f once after a program is created (the
Program
indicator must
be lit, otherwise press
Program
) and the program is played, the Repeat 1 indicator will
light and the track currently playing will be repeated continuously. If
Repeat
is pressed
twice, “Repeat All” will be displayed, all programmed tracks will be played subsequently
and the sequence will be repeated continuously until the Stop button is pressed.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HD990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HD990 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon HD990

Harman Kardon HD990 User Manual - German - 16 pages

Harman Kardon HD990 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info