599843
9
Zoom out
Zoom in
Previous page
1/17
Next page
ENGLISH
INSTALLATION
9
Installation
To prevent possible damage to your speakers
and other components in your audio system,
it is important that ALL components, including
the HD3700 and your receiver or preamp and
amplifiers, are turned off and unplugged from
their AC power source when installing any
new component.
Connecting the HD3700 to your audio system is
simple. Using standard RCA-to-RCA interconnect
cables, connect the left and right Audio Output
jacks on the rear panel to the CD input jacks on
your receiver, surround processor or preamplifier.
If your system includes an optional external
digital-to-analog converter, or if you are using
a receiver or other processor that has the
capability to decode PCM digital input signals,
connect the Digital Output jack to the
Coaxial or Optical Digital input on the decoder.
Make certain to use a coaxial-style interconnect
cable, as standard audio cables will not perform
as well.
Install two AAA batteries by turning the remote
over so that you are holding the bottom side up.
Press lightly on the embossed arrow on the cover
and gently slide the cover towards you in the
direction of the arrow. Insert the batteries inside
the compartment, being careful to follow the
+ and – polarity indications at the bottom of the
compartment. Replace the cover by placing it on
the remote and sliding it back towards the top of
the remote.
Note: When replacing batteries, always replace
both at the same time. When the unit will not
be used for an extended period of time, it is also
a good idea to remove the batteries so that the
potential for corrosion or damage is avoided.
If the HD3700 is installed behind a cabinet
or other obstruction that may block the path
between the front-panel Remote Sensor and
the location of the remote, an optional external
IR sensor maybe used. Connect the sensor to the
Remote IR-In Jack on the rear panel. This jack
may also be connected to the IR Output jack of
another compatible Harman Kardon component
or a compatible IR-system-remote product.
You may also use the IR Sensor in the HD3700
to send commands to other compatible remote
controlled products. Connect the Remote
IR-Out jack to the input of the other product
or system.
Connect the power to an on-switched AC wall
outlet or to the accessory outlet on the rear of
another audio device in your system and you are
ready to go!
Note: When using the accessory outlet on
another product to power the HD3700 make
certain that it has the compatibility to power
a device that draws at least 14 watts of
current in addition to being able to handle the
requirements of the other devices that may be
plugged into the accessory outlets. If you use a
‘switched’ outlet, it is important to remember
that the host product must be turned on in order
for the HD3700 to operate.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HD 3700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HD 3700 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info