Manual Harman Kardon FL8385 (page 10 of 16) (English)

502825

Zoom out

Zoom in

1/16

INSTALLATION AND CONNECTIONS

10 INSTALLATION AND CONNECTIONS

To prevent possible damage to your speakers and

other components in your audio system, it is important

that ALL components, including the FL 8385 and your

receiver or preamp and amplifiers, are turned off and

unplugged from their AC power source when installing

any new component.

Connecting the FL 8385 to your audio system is sim-

ple. Using standard RCA-to-RCA interconnect cords,

connect the left and right

Audio Output Jacks ∞ on

the rear panel to the CD input jacks on your receiver,

surround processor or preamplifier.

If your system includes an optional external digital-to-

analog converter, or if you are using a receiver or

other processor that has the capability to decode PCM

digital input signals, connect the

Coaxial Digital

Output Jack

™ to the Coaxial Digital input on the

decoder. Make certain to use a coaxial-style intercon-

nect cable, as standard audio cables will not perform

as well.

Install the two AA batteries supplied with the

FL 8385’s remote by turning the remote over so that

you are holding the bottom side up. Press lightly on the

embossed arrow on the cover and gently slide the cover

towards you in the direction of the arrow. Insert the bat-

teries inside the compartment, being careful to follow the

+ and

–

polarity indications at the bottom of the com-

partment. Replace the cover by placing it on the remote

and sliding it back towards the top of the remote.

NOTE: When replacing batteries, it is always a good

idea to replace both at the same time. When the unit

will not be used for an extended period of time, it is

also a good idea to remove the batteries so that the

potential for corrosion or damage is avoided.

If the FL 8385 is installed behind a cabinet or other

obstruction that may block the path between the front

panel

Remote Sensor $ and the location of the

remote, an optional external IR sensor may be used.

Connect the sensor to the

Remote Control Input

Jack

¢ on the rear panel. This jack may also be

connected to the IR-Output jack of another compatible

Harman Kardon component or a compatible IR-sys-

tem-remote product.

You may also use the IR Sensor in the FL 8385 to send

commands to other compatible remote controlled prod-

ucts. Connect the

Remote Control Output Jack £

to the input of the other product or system.

Connect the power to a nonswitched AC wall outlet or

to the accessory outlet on the rear of another audio

device in your system and you are ready to go!

NOTE: When using the accessory outlet on another

product to power the FL 8385, make certain that it

has the compatibility to power a device that draws at

least 20 watts of current in addition to being able to

handle the requirements of the other devices that may

be plugged into the accessory outlets. If you use a

“switched” outlet, it is important to remember that

the host product must be turned on in order for the

FL 8385 to operate.

➞

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon FL8385 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon FL8385 Manual

Product: