456609
41
Zoom out
Zoom in
Previous page
1/44
Next page
CONFIGURING THE REMOTE 41
to the next position. Then press the Numeric
Key
A
as required to enter the desired letter.
This is the way you would enter the second “O”
in the word ZOOM, and again for the letter “M.
c. To enter a blank space, press the
Navigation Button
D
twice. The first
press will move the cursor to the right, and
the second press will move the cursor one
more space to the right, leaving a blank space
between the last letter and the next one.
9. Repeat Steps 7 and 8 as needed to complete
entering the needed letters, numbers, characters
and spaces.
10. When the text entry is complete, press the
Set
Button
F
. The new name will be entered into
the remote’s memory, replacing the default name.
11. At this point you have two options:
a. If you wish to program an additional key within
the same device, press the
Set Button
F
as
instructed by the bottom line of the LCD display
reading
ANOTHER KEY. The remote will
return to the
SELECT A KEY menu option
as shown in Step 6. Repeat the instructions in
Steps 6 though 11 to rename the next key.
b. If you have no additional keys to rename, press
the
Navigation Button
D
once so that
the menu screen displays
EXIT on the bottom
line of the display. Press the
Set Button
F
to return the remote to normal operation.
NOTES ON RENAMING KEYS:
• Renaming a key does not change its function. You
may change the function of an individual key by
learning a new code into the remote. See page 34
for more information.
When a key is renamed it will only apply to the
specific device selected in Step 4. The same key
may be renamed as needed for each individual
device with which it is used.
Resetting the Remote
Depending on the way in which the remote has been
programmed, there may be a situation where you wish
to totally erase all changes that have been made to
the remote and return it to the factory defaults. You
may do that by following the steps shown below, but
remember that once the remote is reset, ALL changes
that have been made, including programming for use
with other devices, learned keys, macros, punch-
through settings and key names, will be erased and
any settings you had previously made will have to be
reentered.
To erase all settings and reset the remote to the
original factory default settings and displays, follow
these steps:
1. Press and hold the
Program Button
O
for
about three seconds while the message shown
in Figure 15 appears in the remote’s
LCD
Information Display
2
. Release the button
when the red light under the
Set Button
F
appears.
2.
The remote’s MAIN MENU message (Figure 16),
will appear in the LCD display and the Set Button
F
will remain illuminated in red. Press the
/
¤
Navigation Buttons n until USER
RESET
appears on the bottom line of the LCD
screen, as shown in Figure 74.
Figure 74
3. Press the Set Button
F
to reset the remote.
Note that once the Set Button is pressed the
process may not be stopped. While the remote’s
memory is being cleared a
RESETTING...
message will appear in the upper line of the
remote’s LCD screen as shown in Figure 75.
It may take a few minutes for the reset process
to take place, and the length of time will vary
depending on how much customization and
programming has taken place. Please be patient;
as long as the message appears in the display the
remote is functioning properly.
Figure 75
4. When the remote has been totally reset and
returned to the factory default condition, a
REMOTE RESET COMPLETE message will
appear (Figure 76) briefly, and then the remote
will return to normal operation.
Figure 76
Additional Notes on Configuring and Operating
the Remote:
When the remote is being programmed, it will auto-
matically time-out if no button is pressed within a
thirty-second period. The message shown in Figure
77 will appear briefly, and the remote will then exit
the feature being programmed and any data entered
will be lost.
Figure 77
The programming or configuration process may
also be stopped at any time by pressing the
Clear
Button
9
. The message shown in Figure 77
will appear, the data entered in the current process
will be lost and the remote will return to normal
operation. Any process that was underway when
the button will be pressed must be re-started.
• Extensive use of the programming, learning and
configuration functions of the remote may consume
significantly more battery power than normal remote
operation. While the batteries should last for four to
six months in normal operation, you may find that
they need to be changed sooner after the remote is
programmed for the first time.
When the batteries approach a level below which
the remote will not function, the remote’s LCD
screen will display a
LOW BATTERY warning as
shown in Figure 78. We strongly recommend
replacing the batteries as soon as this message
appears to avoid the loss of programming and con-
figuration settings. These settings are
not lost when
the batteries are changed quickly.
Figure 78
The remote has a built-in backlight that may be
activated by pressing the
Light Button
P
. This
button is made from a special “glow” material so
that it is easier to find in dark rooms. This glow
feature does not consume any electricity, but the
glow will fade when the remote is kept in a dark
location for an extended period of time. The “glow”
feature may be restored by placing the remote in
normal room light for a few hours.
The remote’s backlight will remain lit for approxi-
mately five seconds after the
Light Button
P
is
pressed, and it will stay lit for another five seconds if
any key is pressed while the backlight is on. You
may keep the backlight lit by holding the Light
Button, but extensive use of the backlight will
reduce battery life.
The LCD display will remain on for ten seconds
after a key is pressed and then turn off to conserve
battery life.
When any button is held for more than thirty
seconds the LCD will turn off and the remote will
stop transmitting the codes to conserve battery life.
AVR
LOW BATTERY
TIME OUT OR
CLR KEY PRESSED
REMOTE RESET
COMPLETE
RESETTING...
MAIN MENU
USER RESET
CONFIGURING THE REMOTE
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon DPR 1001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon DPR 1001 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info