502796
28
Zoom out
Zoom in
Previous page
1/52
Next page
28 SYSTEM CONFIGURATION
System Configuration
When the CHANNEL ADJUST menu first
appears, the test tone is off. Use the
/
¤
Navigation Button
D
to select any channel
for adjustment using an external source, such as
a test disc, from which to judge the output levels.
After the cursor is pointing to the channel to
be adjusted, press the
/
Navigation Button
Ea
to raise or lower the output level.
However, before proceeding with any manual
adjustment we recommend that you first use the
AVR’s internal test tone generator and automatic
sequencer to send a tone to each channel so that
you may verify that all speaker connections have
been properly made.
5. To turn the test tone on and have it automati-
cally circulate among the channels where a
speaker has previously been configured (see
page 21), press the
/
¤
Navigation
Button
D
until the cursor is pointing to
the
TEST TONE SEQ line on the menu.
Next, press the
/
Navigation Button
Ea
until AUTO is shown. At this time
the test tone will immediately begin to circu-
late clockwise around the room, playing for
two seconds in each speaker before switching
to the next speaker position. The cursor will
blink next to the active speaker to indicate
which speaker the sound should be coming
from.
IMPORTANT NOTE: Because this test noise will
have a much lower level than normal music, the
volume must be lowered after the adjustment for
all channels is made, but BEFORE you return to
the main menu and the test tone turns off.
NOTE: Remember to verify that the speakers have
been properly connected. As the test noise
circulates, listen to make certain that the sound
comes from the speaker position shown in the
Main Information Display
Ò
. If the sound
comes from a speaker location that does NOT
match the position indicated in the display, turn
the AVR off using the Main Power Switch
1
and check the speaker wiring or connections to
external power amplifiers to make certain that
each speaker is connected to the correct output
terminal.
6. After checking for speaker placement, let the
test noise circulate again, and listen to see
which channels sound louder than the others.
Using the front left speaker as a reference,
press the
/
Buttons
Ea
on the remote
to bring all speakers to the same volume level.
When one of the
/
buttons is pushed, the
test noise circulation will pause on the channel
being adjusted to give you time to make the
adjustment. When you release the button, the
circulation will resume after five seconds. The
on-screen cursor and the test noise can also
be moved directly to the speaker to be
adjusted by pressing the
/
¤
buttons
D
on the remote.
7. Continue to adjust the individual channels
until the volume level sounds the same from
each speaker. Note that adjustments should be
made with the
/
Buttons
Ea
on the
remote only, NOT the main volume controls.
If you are using a sound-pressure level (SPL)
meter for precise level adjustment with the test
tone, open the main Volume Control
d
to
–15dB and set the individual output level for
each channel so that the meter reads 75dB,
C-Weighted Slow. After all settings are made turn
the main volume down.
You may also make these same adjustments with
complete manual control over the channel being
adjusted by pressing the
/
¤
Navigation
Button
D
until the cursor is pointing to the
TEST TONE SEQ line on the menu and then
using the
/
Navigation Button
Ea
to
select
MANUAL in the highlighted video. In the
MANUAL mode, the test tone will also start
immediately, but the tone will only be moved to
another channel by pressing the
/
¤
Navigation Button
D
. When the manual
sequencing mode is active, the tone is turned off
by pressing the
/
¤
Navigation Button
D
until the cursor is pointing to the TEST
TONE line and the
/
Navigation Button
Ea
is then pressed to select OFF in the
highlighted video.
If you find that the output levels are either
uncomfortably low or high, you may repeat the
procedure. Return to Step 2 and adjust the
master volume either slightly higher or lower to
accommodate your particular room layout and
your tastes. You may repeat this procedure as
many times as necessary to achieve a desired
result. In order to prevent possible damage to
your hearing or your equipment, we emphasize
that you should avoid setting the master volume
above 0dB.
When all channels have an equal volume level,
the adjustment is complete. Use the
/
¤
Buttons
D
to move the cursor next to the
TEST TONE line, and press the
/
Buttons
Ea
until the word OFF appears to stop the
test tone.
Note that any time a given surround mode is
selected, even for a different source input, these
output level settings will be used. However, the
output levels must be set independently for each
surround mode, including variations such as Dolby
Pro Logic II-Movie versus Dolby Pro Logic II-Music.
Although this may seem to be tedious, it is neces-
sary in order to optimize the AVR’s performance
when differing methods are employed to steer the
audio materials to the various channels. However,
the AVR will carry over the settings for one mode
to the same mode in a different channel configu-
ration, such as Dolby Pro Logic II-Movie and Dolby
Pro Logic II-Movie. If you wish, as a shortcut to
get started quickly, you may set the levels for
Dolby Pro Logic II-Movie and copy down those
settings, reentering them for each of the Dolby
modes and entering the settings only for those
speakers which are available for each mode.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon cineparis 7bq (avr155 - dvd29) at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon cineparis 7bq (avr155 - dvd29) in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon cineparis 7bq (avr155 - dvd29)

Harman Kardon cineparis 7bq (avr155 - dvd29) User Manual - English, Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info