4 SAFETY INFORMATION
Safety Information
Important Safety Information
READ THIS BEFORE OPERATING
YOUR UNIT
Do not install this equipment in a confined space
such as a case or similar – away from direct
sunlight, heat sources, vibration, dust, moisture,
and/or cold. Avoid installing this unit where for-
eign object may fall onto this unit and/or this unit
may be exposed to liquid dripping or splashing.
On the top of this unit, do not place:
– Burning objects (i.e. candles), as they may
cause fire, damage to this unit, and/or personal
injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the
user and/or damage to this unit.
Do not cover this unit with a newspaper, table-
cloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit rises,
it may cause fire, damage to this unit, and/or per-
sonal injury.
Install this unit near the AC outlet and where the
AC power plug can be reached easily.
This unit is not disconnected from the AC power
source as long as it is connected to the wall out-
let, even if this unit itself is turned off. This state is
called the standby mode. In this state, this unit is
designed to consume a very small quantity of
power.
WARNING. TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
Verify Line Voltage Before Use
Your AVR has been designed for use with
220-230-Volt AC current. Connection to a line
voltage other than that for which it is intended
can create a safety and fire hazard and may dam-
age the unit. If you have any questions about the
voltage requirements for your specific model, or
about the line voltage in your area, contact your
dealer before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord
attached to your unit. We do not recommend that
extension cords be used with this product. As with
all electrical devices, do not run power cords
under rugs or carpets or place heavy objects on
them. Damaged power cords should be replaced
immediately by an authorized service depot with a
cord meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC
outlet, always pull the plug, never pull the cord. If
you do not intend to use the unit for any
considerable length of time, disconnect the plug
from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside
this product. Opening the cabinet may present a
shock hazard, and any modification to the prod-
uct will void your guarantee. If water or any metal
object such as a paper clip, wire or a staple acci-
dentally falls inside the unit, disconnect it from
the AC power source immediately, and consult an
authorized service station.
Installation Location
n To assure proper operation and to avoid the
potential for safety hazards, place the unit on a
firm and level surface. When placing the unit
on a shelf, be certain that the shelf and any
mounting hardware can support the weight of
the product.
n Make certain that proper space is provided
both above and below the unit for ventilation.
If this product will be installed in a cabinet or
other enclosed area, make certain that there is
sufficient air movement within the cabinet.
Under some circumstances a fan may be
required.
n Do not place the unit directly on a carpeted
surface.
n Avoid installation in extremely hot or cold
locations, or an area that is exposed to direct
sunlight or heating equipment.
n Avoid moist or humid locations.
n Do not obstruct the ventilation slots on the
top of the unit, or place objects directly over
them.
n Due to the weight of the AVR 155 and the heat
generated by the amplifiers, there is the remote
possibility that the rubber padding on the
bottom of the unit’s feet may leave marks on
certain wood or veneer materials. Use caution
when placing the unit on soft woods or other
materials that may be damaged by heat or
heavy objects. Some surface finishes may be
particularly sensitive to absorbing such marks
due to a variety of factors beyond
Harman Kardon's control, including the nature
of the finish, cleaning materials used, and
normal heat and vibration caused by the use of
the product, or other factors. We recommend
that caution be exercised in choosing an instal-
lation location for the component and in nor-
mal maintenance practices, as your warranty
will not cover this type of damage to furniture.
Cleaning
When the unit gets dirty, wipe it with a clean,
soft, dry cloth. If necessary, wipe it with a soft
cloth dampened with mild soapy water, then a
fresh cloth with clean water. Wipe dry im -
mediately with a dry cloth. NEVER use benzene,
aerosol cleaners, thinner, alcohol or any other
volatile cleaning agent. Do not use abrasive
cleaners, as they may damage the finish of metal
parts. Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect
any interconnection cords with other compo -
nents, and make certain that you disconnect the
unit from the AC outlet.
Unpacking
The carton and shipping materials used to pro-
tect your new receiver during shipment were
specially designed to cushion it from shock and
vibration. We suggest that you save the carton
and packing materials for use in shipping if you
move, or should the unit ever need repair.
To minimize the size of the carton in storage, you
may wish to flatten it. This is done by carefully
slitting the tape seams on the bottom and
collapsing the carton. Other cardboard inserts
may be stored in the same manner. Packing
materials that cannot be collapsed should be
saved along with the carton in a plastic bag.
If you do not wish to save the packaging
materials, please note that the carton and other
sections of the shipping protection are recyclable.
Please respect the environment and discard
those materials at a local recycling center.
It is important that you remove the protective
plastic film from the front-panel lens. Leaving the
film in place will affect the performance of your
remote control.
