502638
40
Zoom out
Zoom in
Previous page
1/60
Next page
To enter a station into the memory, first tune the sta-
tion using the steps outlined above. Then:
1. Press the Memory Button on the remote;
the station’s frequency will flash.
2. Within five seconds, press the Numeric Keys k
corresponding to the memory location where you
wish to store this station’s frequency. Once entered,
the preset number will appear in the Upper
Display Line #.
3. Repeat the process after tuning any additional
stations to be preset.
Recalling Preset Stations
To manually select a station previously entered in
the preset memory, press the Numeric Keys k
for the desired station’s memory location.
To manually scroll through the list of preset stations,
press the Preset Stations Selector Button
6v on the front panel or remote.
Recording
In normal operation, the audio or video source
selected for listening through the AVR 7300 is sent to
the record outputs. This means that any program you
are watching or listening to may be recorded simply
by placing machines connected to the outputs for
Tape Outputs or Video 1/Video 2 Outputs
π∆ in the record mode.
When a digital audio recorder is connected to the
Digital Audio Outputs ϧ , you are able
to record the digital signal using a CD-R, MiniDisc or
other digital recording system.
NOTES:
The digital outputs are active only when a digital sig-
nal is present, and they do not convert an analog
input to a digital signal, or change the format of the
digital signal. In addition, the digital recorder must
be compatible with the output signal. For example,
the PCM digital input from a CD player may be
recorded on a CD-R or MiniDisc, but Dolby Digital
or DTS signals may not.
• The Front-Panel Video 5 jacks may be con-
figured for use as an output, allowing connection to
a recorder, when the steps shown in the section
below are followed.
• Please obey the copyright restrictions on any mate-
rial you copy. Unauthorized duplication of copyright-
ed materials is prohibited by law.
Front-Panel Connections
In addition to the rear-panel digital and analog outputs,
the AVR 7300 offers Harman Kardon’s exclusive con-
figurable front-panel output-jack feature. For easy con-
nection of portable devices, you may switch the front-
panel Video 5 Jacks from an input to an output
by following these steps:
1. Press the OSD Button U to view the
MASTER MENU (Figure 1).
2. Press the Set Button q to enter the
IN/OUT SETUP menu (Figure 2).
3. Press the
¤
Navigation Button o so that the
on-screen
cursor is next to VIDEO 5.
4. Press the Set Button q and then press the
/
Navigation Button o so that the word
OUT is highlighted.
5. Press the Set Button q to enter the change.
6. Press the OSD Button U to exit the menus and
return to normal operation.
Once the setting is made, the Input/Output Status
Indicator will turn red, indicating that the jacks
are now an output, instead of in the default setting as
an input. Once changed to an output, the setting will
remain as long as the AVR 7300 is turned on, unless
the setting is changed in the OSD menu system, as
described above. However, once the AVR 7300 is
turned off, the setting is cancelled. When the unit is
turned on again, the front-panel jacks will return to
their normal default setting as an input. If you wish
to use the jacks as an output at a future time, the
setting must be changed again using the OSD menu
system, as described above.
Output Level Trim Adjustment
Normal output level adjustment for the AVR 7300 is
established using the test tone, as outlined on pages
29–30. In some cases, however, it may be desirable to
adjust the output levels using program material such as
a test disc, or a selection you are familiar with.
Additionally, the output level for the subwoofer can only
be adjusted using this procedure.
To adjust the output levels using program material, first
set the reference volume for the front left and front right
channels using the Volume Control )r
î
.
If you are using a disc with test signals or an external
signal generator as the source used when the output
levels are being trimmed, you may use the remote as
an SPL meter to guide you to the correct level set-
tings. To use the EzSet remote as an SPL meter, follow
the instructions on page 29.
Once the reference level has been set, press the
Channel Select Button n and FRONT L
LEVEL will appear in the Lower Display Line
$. To change the level, first press the Set Button
q, and then use the
/
¤
Navigation Button
o to raise or lower the level. DO NOT use the vol-
ume control, as this will alter the reference setting.
Once the change has been made, press the Set
Button q and then press the
/
¤
Navigation
Button o to select the next output-channel location
that you wish to adjust. To adjust the subwoofer level,
press the
/
¤
Navigation Button o until
WOOFER LEVEL appears in the Lower Display
Line $ or on-screen display.
Repeat the procedure as needed until all channels
requiring adjustment have been set. When all adjust-
ments have been made and no further adjustments
are made for five seconds, the AVR 7300 will return to
normal operation.
The channel output for any input may also be adjusted
using the full-OSD on-screen menu system. First, set
the volume to a comfortable listening level using the
Volume Control
)r
î
. Then, press the OSD
Button U to bring up the MASTER MENU
(Fig. 1). Press the
¤
Navigation Button o until
the on-screen cursor is next to the CHANNEL
ADJUST line. Press the Set Button q to
activate the CHANNEL ADJUST menu (Fig. 13).
Once the menu appears on your video screen, first
use the
/
¤
Navigation Button o to move the
on-screen cursor so that it is next to the TEST
TONE line. Press the
/
Navigation Button o
so that OFF is highlighted. This will turn off the test
tone and allow you to use your external test disc or
other source material as the reference. Then, use the
/
¤
Navigation Button o to select the chan-
nels to be adjusted. At each channel position, use the
/
Navigation Button o to change the output
level. Remember, the goal is to have the output level
at each channel be equal when heard at the listening
position.
If you wish to reset all the levels to their original factory
default of 0dB offset, press the
/
¤
Navigation
Button o so that the on-screen cursor is next to
the CHANNEL RESET line and press the
/
Navigation Button o so that the word ON is
highlighted. After the levels are reset, resume the
procedure outlined above to reset the levels to the
desired settings. When all adjustments are done, press
the
/
¤
Navigation Button o to move the on-
screen cursor so that it is next to BACK TO
MASTER MENU and then press the Set Button
q if you wish to go back to the main menu to
1
5
1
4
1
4
1
3
11
39
OPERATION
40 OPERATION
OPERATION
AVR7300(120v)-OM 6/14/04 9:15 AM Page 40
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR7300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR7300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info