Manual Harman Kardon AVR7300 (page 14 of 60) (English)

502638

Zoom out

Zoom in

1/60

14 MAIN REMOTE CONTROL FUNCTIONS

MAIN REMOTE CONTROL FUNCTIONS

IMPORTANT NOTE: The AVR 7300’s remote may

be programmed to control up to nine devices,

including the AVR 7300. Before using the remote,

it is important to remember to press the Input

Selector Button

that corresponds to the unit

you wish to operate. In addition, the AVR 7300’s

remote is shipped from the factory to operate the

AVR 7300 and most Harman Kardon CD or DVD

players and cassette decks. The remote is also

capable of operating a wide variety of other products

using the control codes that are part of the remote.

Before using the remote with other products, follow

the instructions on pages 46 – 55 to program the

proper codes for the products in your system.

It is also important to remember that many of the

buttons on the remote take on different functions,

depending on the product selected using the Input

Selectors d. The descriptions shown here primarily

detail the functions of the remote when it is used to

operate the AVR 7300.

a Power Off Button: Press this button to place

the AVR 7300 or a selected device in the Standby

mode. Note that this will turn off the main room

functions, but if the Multiroom system is activated,

it will continue to function.

Power On Button: Press this button to turn on

the power to a device selected by first pressing one of

the Input Selectors

LCD Information Display: This two-line screen

displays various information depending on the com-

mands that have been entered into the remote.

Input Selectors: Pressing one of these buttons

will perform three actions at the same time. First, if the

AVR 7300 is not turned on, this will power up the unit.

Next, it will select the source shown on the button as

the input to the AVR 7300. Finally, it will change the

remote control so that it controls the device selected.

After pressing one of these buttons, you must press

the AVR Selector Button

again to operate the

AVR 7300’s functions with the remote.

AVR Selector: Pressing this button will switch the

remote so that it will operate the AVR 7300's functions.

If the AVR 7300 is in the Standby mode, it will also turn

the AVR 7300 on.

DSP Surround Mode Selector: Press this

button to select one of the DSP surround modes, such

as VMAx, Hall 1, Hall 2 or Theater. Each press of the

button selects another mode. (See page 36 for more

information on surround modes.)

g Test Button: Press this button to begin the

sequence used to calibrate the AVR 7300’s output

levels. (See page 29 for more information on calibrat-

ing the AVR 7300.)

h Video Processing On/Off Button: Press this

button to turn the video processing circuits on or off.

See page 31 for more information.

Direct Button: Press this button when the tuner

is in use to start the sequence for direct entry of a

station’s frequency. After pressing the button, simply

press the proper Numeric Keys

to select a

station. (See page 39 for more information on the tuner.)

Clear Button: When programming the remote

or using the EzSet feature, press this button to cancel

the current function. When using the remote to enter

frequencies for direct tuner access, press this button

to clear previous entries.

Numeric Keys: These buttons serve as a 10-

button numeric keypad to enter tuner preset positions.

They are also used to select channel numbers when

TV, Cable or SAT has been selected on the remote, or

to select track numbers on a CD, DVD or LD player,

depending on how the remote has been programmed.

These buttons are also used to enter letters and num-

bers when renaming devices in the LCD Information

Display. (See page 53 for more information on renam-

ing devices and keys.)

Tuning Mode Button: Press this button to

change the tuner mode between manual and

automatic. When the button is pressed so that

AUTO/STEREO appears in the Upper

Display Line # and in the on-screen display, only

stations with acceptable signal quality will be tuned,

and the tuner will play FM stations in stereo, when

available. In the AUTO mode, when the Tuning

Up/Down Buttons 4w

≠

are pressed, the unit

will automatically search for the next available station

with good signal strength. When this button is pressed

so that MANUAL/MONO appears in the Upper

Display Line # and in the on-screen display, each

press of the Tuning Up/Down Buttons 4w

≠

will move the frequency up or down in single-step

increments. When the FM band is in use, pressing the

button so that the MANUAL mode is activated will

enable you to tune stations with weak signals by

changing to monaural reception. (See page 39 for

more information on tuner operation.)

m Dim Button: This button activates the Dimmer

function, which reduces the brightness of the front-

panel display, or turns it off entirely. Press the button

once to reduce the display brightness by 50%, and

press it again within five seconds and the main display

will go completely dark. Note that this setting is tem-

porary; regardless of any changes, the display will

always return to full brightness when the AVR is turned

on. The blue accent lighting inside the Volume

Control ) and the Input/Output Indicator

will go out when the panel lights are at half brightness

or fully dimmed.

n Channel Select Button: This button is used to

start the process of setting the AVR 7300’s output levels

to an external source. Once this button is pressed, press

the

⁄

on the Navigation Button o to select the

channel being adjusted, then press the Set Button q,

followed by the

⁄

on the Navigation Button

again, to change the level setting. (See page 40 for more

information.)

Navigation Button: This single disc-like button is

used to navigate through the on-screen configuration

menus, to scroll through the options list and to select

choices for the various settings such as delay, speakers,

surround modes, digital inputs, etc. To use the button,

simply press it left, right, up or down in the direction

indicated by the

⁄

/¤/‹ /› icons printed on the but-

ton disc. Depending on the menu being used, press-

ing the button will either change a specific menu or

configuration choice or change the option shown in

the on-screen or front-panel display. The sections in

this manual describing the unit’s individual features and

configuration options contain specific information on

how the navigation controls are used.

Digital Select Button: Press this button to assign

one of the digital inputs ®† to a source.

(See page 37 for more information on using digital

inputs.)

Set Button: This button is used to enter settings

into the AVR 7300’s memory. It is also used in the

setup procedures for delay time, speaker configuration

and channel output level adjustment.

Volume Up/Down Buttons: These controls

share the disc in the lower portion of the remote with

the Channel Up/Down Selector Y. To raise the

volume, press the button marked

⁄

by pressing

towards the top of the remote. To lower the volume,

press the button marked

by pressing towards the

bottom of the remote. The

‹

›

buttons on the left and

right sides of this disc change channels up or down

when the TV, cable box or satellite Input Selectors

have been pressed.

MAIN REMOTE CONTROL FUNCTIONS

14 MAIN REMOTE CONTROL FUNCTIONS

AVR7300(120v)-OM 6/14/04 9:15 AM Page 14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR7300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR7300 Manual

Product: