Manual Harman Kardon AVR7200 (page 45 of 52) (English)

502637

Zoom out

Zoom in

1/52

CONFIGURING THE REMOTE

CONFIGURING THE REMOTE 45

To restore the EzSet feature to normal operation,

repeat the procedure outlined above, except that in

Step 3 you should press the

⁄

Navigation

Button n so that EZSET ENABLE appears in the

lower line of the LCD display. When that display

appears, press the Set Button

and the EzSet fea-

ture will be reactivated. You may then press the Clear

Button

to exit the remote’s menu system and

return to normal operation or press the Set Button

again to immediately use the EzSet feature to

calibrate the system as shown on pages 24 – 25.

Renaming

While the names given to the buttons and inputs on the

remote represent recognizable categories of audio/

video products, system operation may be easier if the

displays shown in the remote’s LCD screen are cus-

tomized to reflect the specific characteristics of a play-

back source’s brand name or the new function given to

a specific button when one remote’s controls are pro-

grammed into the AVR remote. The AVR remote allows

you to change the name of either a master device or

any button on the remote using the following steps.

Renaming a Device

To rename a specific device/input source button, follow

these steps. For this example, we will show you how to

rename the Device/Input Selector normally shown as

“TV” to “HDTV TUNER.”

1. Press and hold the

Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s

LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

Navigation Button n until RENAME appears

on the bottom line of the LCD screen, as shown in

Figure 66.

Figure 66

3. At the next menu screen press the

⁄

Navigation Button n until RENAME

DEVICE appears on the bottom line of the

LCD screen, as shown in Figure 67. Press the

Set Button

to begin renaming a device.

Figure 67

4. The next display screen (Figure 68) is where you

select the device that will be renamed. In our

example, that is the TV button. Press the

⁄

Navigation Button n until the name of the

base device appears and then press the Set

Button

Figure 68

5. At the next menu screen you will see the device

name on the bottom line of the display with a

blinking cursor box to the right of the device name.

Press the

‹

Navigation Button n to return the

blinking cursor to the far left side of the display

line. You may then retitle the device name as

shown in the next step.

6. To enter the new name, press the

Numeric Keys

. The letters above the numbered buttons indi-

cate which letter or symbol will appear when the

button is pressed during the renaming process.

The first press of the button will enter the first letter

shown, subsequent presses of the same button will

change the display to the other letters above that

numbered key. For example, since the first letter

we need to rename the input to HDTV Tuner is an

“H”, you would locate the “H” above the “4” but-

ton, and press the button twice. The first press

shows a “G,” the second press changes it to an

“H.” Consult the table at the end of this section to

see which characters pressing a particular button

generates.

7. After you enter the first letter of the new device

name, there are three options for entering the next

character:

a. To enter a letter that requires a different

numeric key to be pressed, simply press that

button. The cursor will automatically move to

the next position and the first letter accessed

by the new button will appear. Following our

example, the next letter needed is a “D,” so

you would press the “3” button once.

b. To enter a letter that uses the same numeric

key, you must first press the

›

Navigation

Button

to move the blinking cursor block

to the next position. Then press the Numeric

Key

as required to enter the desired letter.

To enter a blank space, press the

›

Navigation

Button

twice. The first press will move the

cursor to the right, and the second press will

move the cursor one more space to the right,

leaving a blank space between the last letter and

the next one.

8. Repeat Step 7 as needed to enter all the needed

letters, numbers, characters and spaces.

9. When the text entry is complete, press the

Set Button

. The LCD display will blink

DEVICE RENAMED three times and then return

to normal operation.

Once a device is renamed you will see the new name

on the top line of the remote’s LCD display whenever

the

Input//Device Selector

is pressed, or when

any other command/function button on the remote is

pressed after the main Device Selector is pressed.

Note that renaming a device in the remote will

not

change the name of the input used by the on-screen

menu system of the AVR 7200.

NOTES ON RENAMING DEVICES:

• To move the cursor to the right or left of the display

during the renaming process, press the

‹

›

Navigation Buttons

as required.

• The table below shows the letters, numbers and

characters that may be accessed by pressing the

Numeric Keys:

Key Characters Key Characters

1 [,],/,1 6 M,N,O,6

2 A,B,C,2 7 P,Q,R,S,7

3D,E,F,3 8 T,U,V,8

4G,H,I,4 9 W,X,Y,Z,9

5J,K,L,5 0 -,.,#,0

• Renaming a device changes the name of the device

only, not any of the individual key functions within

that device memory. To change the name of an

individual device, follow the instructions in the next

section.

Renaming Individual Keys

Thanks to the programming flexibility of the AVR

remote, an individual button on the remote may be

assigned a feature or function that is different from the

name that appears as the factory default when the but-

ton is pressed. However, with the Rename Key function

it is possible to rename almost any button on the

remote so that when the button is pressed you will see

a more descriptive or appropriate name displayed.

To rename a specific button on the remote, follow

these steps. For this example, we will show you how to

rename the

DSP Surround Mode Selector

which is normally not used when DVD is selected, so

that it reads ZOOM in the remote’s display.

1. Press and hold the Program Button

for

about three seconds while the message shown

in Figure 15 appears in the remote’s LCD

Information Display

. Release the button

when the red light under the Set Button

appears.

The remote’s MAIN MENU message (Figure 16),

will appear in the LCD display and the Set Button

will remain illuminated in red. Press the

⁄

RENAME DEVICE

RENAME

RENAME DEVICE

MAIN MENU

RENAME

AVR 7200 OM 1/27/03 4:47 PM Page 45

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR7200 in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR7200 Manual

Product: