502558

Harman Kardon AVR645 Manual

61
Zoom out
Zoom in
Previous page
1/68
Next page
PROGRAMMING THE REMOTE 61
ENGLISH
Programming the Remote
3. At the next menu screen press the
⁄¤
Navigation Buttons
E
until RENAME
KEY appears on the bottom line of the LCD
screen, as shown in Figure 77. Press the Set
Button
F
to continue.
Figure 77
4. The next display screen (Figure 78) is where
you select the device within which the key to
be renamed exists. Press the
⁄¤
Navigation Buttons
E
until the name of
the base device appears. In our example, since
we want to rename a button within the DVD
device memory, DVD should appear in the
lower line of the LCD. When the desired device
name appears, press the Set Button
F
.
Figure 78
5. At the next menu screen you will select the
first button within the device to be renamed,
as instructed in the display shown in Figure
79. Select the button by simply pressing it on
the remote.
Figure 79
6. Depending on whether or not the button
pressed already has a named function within
the device selected, one of two things will
happen.
a. If the button to be renamed already has a
pre-programmed, or previously renamed
title in the remote’s memory, you will see
that name on the top line of the LCD
display, and a blinking block cursor will
appear on the far left side of the bottom
line of the display, as shown in Figure 80.
b. If the button to be renamed does not have
a function in the device selected, the top
line of the LCD screen will be blank, and a
blinking block cursor will appear on the far
left side of the bottom line of the display,
as shown in Figure 81.
Figure 80
Figure 81
7. To enter the new name for the key, press the
Numeric Keys
H
. The letters above the
numbered buttons indicate which letters or
symbols will appear when the button is
pressed during the renaming process. The first
press of the button will enter the first
character shown, subsequent presses of the
same button will change the display to the
other letters above that numbered key. For
example, since the first letter we need to
rename the Tone button to Zoom is a “Z,” so
you would locate the “Z” above the “9”
button, and press the button four times. The
first press shows a “W,” the subsequent
presses step through the other letters available
until the “Z” appears. Consult the table on the
previous page to see which characters are
available by pressing a particular button.
8. After you enter the first letter of the new
device name, there are three options for
entering the next character:
a. To enter a letter that requires a different
numeric key to be pressed, simply press
that button. The cursor will automatically
move to the next position and the first
letter accessed by the new button will
appear. Following our example, the next
letter needed is an “O,” so you would press
the “6” button once.
b. To enter a letter that uses the same
numeric key, you must first press the
›
Navigation Buttons
E
to move the
blinking cursor block to the next position.
Then press the Numeric Key
H
as
required to enter the desired letter. This is
the way you would enter the second “O” in
the word ZOOM, and again for the letter
“M.”
c. To enter a blank space, press the
›
Navigation Buttons
E
twice. The first
press will move the cursor to the right, and
the second press will move the cursor one
more space to the right, leaving a blank
space between the last letter and the next
one.
9. Repeat Steps 7 and 8 as needed to complete
entering the needed letters, numbers,
characters and spaces.
10. When the text entry is complete, press the
Set Button
F
. The new name will be
entered into the remote’s memory, replacing
the default name.
11. At this point you have two options:
a. If you wish to program an additional key
within the same device, press the Set
Button
F
as instructed by the bottom
line of the LCD display reading ANOTHER
KEY. The remote will return to the
SELECT A KEY menu option as shown in
Step 6. Repeat the instructions in Steps 6
though 11 to rename the next key.
b. If you have no additional keys to rename,
press the
⁄
Navigation Buttons
E
once so that the menu screen displays
EXIT on the bottom line of the display.
Press the Set Button
F
to return the
remote to normal operation.
Notes on Renaming Keys:
• Renaming a key does not change its function.
You may change the function of an individual
key by learning a new code into the remote.
See page 54 for more information.
• When a key is renamed it will only apply to the
specific device selected in Step 4. The same key
may be renamed as needed for each individual
device with which it is used.
Resetting the Remote
Depending on the way in which the remote has
been programmed, there may be a situation
where you wish to totally erase all changes that
have been made to the remote and return it to
the factory defaults. You may do that by
following the steps shown below, but remember
that once the remote is reset, ALL changes that
have been made, including programming for use
with other devices, learned keys, macros, punch-
through settings and key names, will be erased
and any settings you had previously made will
have to be reentered.
To erase all settings and reset the remote to the
original factory default settings and displays,
follow these steps:
1. Press and hold the Program Button
a
for
about three seconds while the message shown
in Figure 25 appears in the remote’s LCD
Information Display
2
. Release the
button when the red light under the Set
Button
F
appears.
2. The remote’s MAIN MENU message (Figure
26), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until USER RESET appears on the
bottom line of the LCD screen, as shown in
Figure 82.
Figure 82
MAIN MENU
USER RESET
DISC SKIP
SELECT A KEY
SELECT A DEVICE
DVD
RENAME
RENAME KEY
29851_AVR645_ENG 30/10/06 9:46 Side 61
… 61 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR645 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info