Manual Harman Kardon AVR645 (page 48 of 68) (English)

502558

Zoom out

Zoom in

1/68

48 ADVANCED FEATURES

Advanced Features

Semi-OSD Settings

The semi-OSD system places one line messages

at the lower third of the video display screen

whenever the Volume, Input Source, Surround

mode or tuner frequency of any of the configura-

tion settings are changed. The semi-OSD system

is helpful in that enables you to have feedback

on any control changes or remote commands

using the video display when it is difficult to view

the front-panel displays. However, you may

occasionally prefer to turn these displays off for a

particular listening session. You may also want to

adjust the length of time the displays remain on

the screen. Both of those options are possible

with the AVR.

To turn off the semi-OSD system, you will need to

make an adjustment in the

ADVANCED

SELECT

menu (Figure 23). To start the adjust-

ment, press the OSD button

to bring the

MASTER MENU to the screen. Press the

⁄

Button

, until the on-screen ➞ cursor is next

to the

ADVANCED line. Press the Set Button

to enter the ADVANCED SELECT

menu.

At the

ADVANCED SELECT menu make

certain that the on-screen ➞ cursor is next to the

SEMI OSD line by pressing the

⁄

buttons

as needed. Next, press the

›

button

that the word

OFF is highlighted in the video

display.

Note that this setting is temporary and will

remain active only until it is changed or until the

AVR is turned off. Once the unit is turned off, the

semi-OSD displays will remain activated, even if

they were switched off for the previous listening

session.

To change the length of time that the semi-OSD

displays remain on the screen, go to the

ADVANCED SELECT Menu as outlined

earlier, and press the

⁄

buttons

needed, until the on-screen ➞ cursor is next to

the

SEMI-OSD TIME OUT line. Next,

press the

‹

›

Buttons

until the desired time

in seconds is displayed. Note that unlike most of

the other options in this menu, this is a

permanent setting change, and the time-out

entry will remain in effect until it is changed,

even when the unit is turned off.

If you wish to make other adjustments in the

menu, press the

⁄

Buttons

until the on-

screen ➞ cursor is next to the desired setting or

the

BACK TO MASTER MENUline and

press the Set button

. If you have no other

adjustments to make, press the OSD Button

to exit the menu system.

Full-OSD Time Out Adjustment

The FULL OSD menu system is used to

simplify the setup and adjustment of the AVR

using a series of on-screen menus. The factory

default setting for these menus leaves them on

the screen for 20 seconds after a period of

inactivity before they disappear from the screen

or Time Out. This Time Out is a safety measure to

prevent the menu text from burning into the

CRTs in your monitor or projector, which might

happen if they were left on indefinitely. However,

some viewers may prefer a slightly longer or

shorter period before the Time Out display.

To change the Full-OSD Time Out, you will need

to make an adjustment in the

ADVANCED

SELECT

menu (Figure 23). To start the adjust-

ment, press the OSD button

to bring the

MASTER MENU to the screen. Press the

⁄

button

, until the on-screen ➞ cursor is next

to the

ADVANCED line. Press the Set Button

to enter the ADVANCED SELECT

menu (Figure 23).

At the

ADVANCED SELECT menu make

certain that the on-screen ➞ cursor is next to the

FULL OSD TIME OUT line by pressing the

⁄

Buttons

as needed. Next, press the

‹

›

buttons

until the desired time is dis-

played in seconds. Note that unlike most of the

other options in this menu, this is a permanent

setting change, and the time-out entry will

remain in effect until it is changed, even when

the unit is turned off.

If you wish to make other adjustments in the

menu, press the

⁄

Buttons

until the

on-screen ➞ cursor is next to the desired setting

or the

BACK TO MASTER MENUline and

press the Set button

. If you have no other

adjustments to make, press the OSD Button

to exit the menu system.

DMP/ Auto Power

When using Harman Kardon’s optional

iPod docking station, the normal operation is to

have the iPod selected as the input source only

when it is specifically chosen. However, you may

set the AVR so that whenever the iPod is turned

on, the AVR will also turn on automatically and

set The Bridge as the input.

To change the setting, first make certain that the

ADVANCED SELECT menu (Figure 23) is

on the screen, and then press the

⁄

Navigation Buttons

F until the cursor is

pointing to

DMP AUTO POWER. Press the

⁄

Navigation Buttons

F so that ON

is highlighted to have the AVR turn on in sync

with an iPod, or

OFF for standard operation.

The

Brid

The

Brid

29851_AVR645_ENG 30/10/06 9:46 Side 48

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR645 Manual

Product: