502558
37
Zoom out
Zoom in
Previous page
1/68
Next page
SYSTEM CONFIGURATION 37
ENGLISH
System Configuration
To return to the settings established by Ezset/EQ,
even if you have made manual changes to the
output trims using the steps shown above, press
/
¤
Navigation Button
E
F so that the
cursor is pointing to the
EZSET
SETTINGS
line and then press the
/
¤
Navigation Button
E
F once so ON
appears in highlighted video. Remember that
after turning the Ezset/EQ settings back on you
must turn return to this menu line and change
the setting to
OFF if you wish to make any
manual trim adjustments.
The final setting in this menu enables you to
have the output levels remain the same for all
inputs or to be adjusted differently for each (or
any) input. While most listeners prefer to keep
the same output levels for all sources, you may
wish to raise or lower some channels, particularly
the subwoofer output for a specific source such
as a CD that is primarily used for music playback.
To enter individual settings for a specific channel,
first make sure that you have either run Ezset/EQ
and/or made any desired manual trim adjust-
ments to set a baseline for all channels. After
that is done, press the OSD Button E to exit
the menu system and then select the input for
which you wish to enter different level settings
by using either the Input Source Selectors
%
on the front panel or the buttons on the remote
that are used to select an input source BC
D. Next, return to the
CHANNEL
OUTPUT
submenu using the steps outlined
above.
At the
CHANNEL OUTPUT menu press
/
¤
Navigation Button
E
F until the
cursor is pointing to the
LEVEL TRIM line
and then press the
/
¤
Navigation Button
E
F once so that INDEPENDENT
appears in highlighted video. When this setting is
active you may change the channel output levels
for any input without changing the settings
previously established for another.
When all changes to the Channel Output levels
and the associated level trim settings have been
made press the
/
¤
Navigation Button
E
F until the cursor is on the BACK TO
MANUAL SETUP
menu and then pressing
the Set Button
F
Q so that you may make
any other adjustments to the system parameters.
If the changes just made complete the manual
adjustments needed, press the OSD Button E
to exit the menu system and resume normal
system operation.
Additional Input Adjustments
After one input has been adjusted for Surround
mode, digital input (if any), speaker type, and
output levels, go back to the
IN/OUT
SETUP
line on the MASTER MENU
(Figure 7) and enter the settings for each input
that you will use. In most cases, only the digital
input and surround mode will be different from
one input to the next, while the speaker type,
crossover frequency, Night mode and output
level settings will usually be the same and may
be quickly entered by entering the same data
used for the original input.
Once the settings outlined on the previous pages
have been made, the AVR is ready for operation.
While there are some additional settings to be
made, these are best done after you have had an
opportunity to listen to a variety of sources and
different kinds of program material. These
advanced settings are described on pages 47 to
48 of this manual. In addition, any of the settings
made in the initial configuration of the unit may
be changed at any time. As you add new or dif-
ferent sources or speakers, or if you wish to
change a setting to better reflect your listening
taste, simply follow the instructions for changing
the settings for that parameter as shown in this
section.
Having completed the setup and configuration
process for your AVR, you are about to
experience the finest in music and home theater
listening. Enjoy!
29851_AVR645_ENG 30/10/06 9:46 Side 37
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR645 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR645 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR645

Harman Kardon AVR645 User Manual - German - 68 pages

Harman Kardon AVR645 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info