502651
23
Zoom out
Zoom in
Previous page
1/32
Next page
System Configuration
With the correct delay time figures for
your listening room calculated, first make
certain that the unit is in the Dolby Pro
Logic mode by pressing the Surround
Mode
button Ò or Dolby Surround
Mode
buttons ` until the Pro Logic
indicator C is illuminated.
Press the Select button j to begin the
adjustment process. The Information
Display
F
will show the current delay
setting, such as REAR - 15mS. If
adjustment is required, immediately
press the Delay button g on the
remote to change the setting until it is
closest to the desired time. Within five
seconds the display will return to normal
readout and the setting will be entered.
The Dolby Digital mode also provides a
separate setting for the center channel
delay mode, since the discrete nature
of Dolby Digital signals makes the
location of the center channel speaker
more critical. To set the delay for the
center channel, measure the distance
from the preferred listening position in
the center of the room to both the center
channel speaker and either the left or
right speaker.
If the distances are equal, no further
adjustment is required, and the center
delay should be set to zero. If the
distance to the front speakers is greater
than the distance to the center speaker
you may wish to reposition the speakers
by moving the front left/right speakers
closer to the listening position or the
center speaker further away from the
listening position.
If repositioning of the speakers is not
possible, adjust the center delay time
so that you add one millisecond of center
channel delay for each foot that the dis-
tance to the center speaker lags behind
the front speakers. For example, if the
front left/right speakers are each 10 feet
from the listening position and the center
channel speaker is 8 feet away, the delay
is figured as 10-8=2, suggesting an
optimal center delay of 2 milliseconds.
To change the delay settings for Dolby
Digital operation, first calculate the
correct timings as outlined above. Next,
make certain that the AVR55 is in the
Dolby Digital mode by pressing the
Dolby Digital/AC-3 button Ûzon
the front panel or remote. Make certain
that the Dolby Digital Indicator B
is illuminated.
Press the
Select button j and note
that the Information Display
F
will
show the settings for both the center and
rear/surround delay as
C-0mS R-10mS.
The center channel delay figure will
blink, indicating that you may change
the setting.
Press the
Delay button g to change
the center delay time to the desired
setting. When the appropriate number
is shown press the
Select button j
once so that the number for rear/
surround delay time on the right side
of the display blinks.
Use the Delay button g to change
the rear/surround delay to the desired
setting.
When both settings are correct, press the
Select button j again and note that
the display will stop blinking. After a few
seconds the display will return to normal
operation and the settings will be entered
to memory.
24
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR55 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info