502644

Harman Kardon AVR35 Manual

33
Zoom out
Zoom in
Previous page
1/45
Next page
Programming the Remote
Example: To program your TV,
Cable Box and the AVR35 to turn on
when the Power button is pressed,
first press-and-hold the AVR b
and Mute buttons ` until the red
light comes on under the AVR but-
ton. Next, press the Mute button
` to enter the Power command
for the AVR. Press the TV Device
Control Selector c to select
the TV mode, and then press the
Mute button ` again, to select
TV Power. Finally, press the CBL
Device Control Selector c
followed by the Mute button `
to select Cable Power. Press the
Channel
⁄
/
¤
buttons f to
enter the commands.
After following these steps, each time
you press the Power button d, the
remote will send the Power On/Off
command each time the Power
button is pressed.
To remove a macro program, follow steps
1, 2 and 4 above, but do not follow step
three. For example, to erase the macro
just entered, press the Device Control
Selector c and the Mute button `
at the same time until the red light
under the Device Control Selector turns
on. Press the Power button d, and
then press the Channel
⁄
/
¤
buttons
f. The red light under the Device
Control Selector will blink twice to
confirm the data entry and then turn off.
NOTE: Only the AVR button b and
the SAT/CBL button c may be pro-
grammed for macros.
Volume Punch-Through
The AVR35’s remote may be programmed
to operate the Volume Controls
from either the TV or the AVR to operate in
conjunction with any of the eight devices
controlled by the remote. For example,
since the AVR35 will likely be used as the
sound system for TV viewing, you may
wish to have the AVR’s volume activated
although the remote is set to run the TV.
Either the AVR or TV volume control may
be associated with any of the remote’s
devices. To program the remote for Volume
Punch-Through, follow these steps:
1. Press the Device Control Selector
c for the unit you wish to have asso-
ciated with the volume control and the
Mute button ` at the same time
until the red light illuminates under
the Device Control Selector.
2. Press the Volume Up button .
3. Press either the AVR b or the TV
Device Control Selector c,
depending on which system’s volume
control you wish to have attached for
the punch-through mode. Note that
the red light under the Device
Control Selector will blink twice
and then go out to confirm the data
entry.
Example: To have the AVR’s
volume control be activated even
though the remote is set to control
the TV, first press the TV Device
Control Selector c and the
Mute button ` at the same time.
Next, press the Volume Up button
followed by the AVR Device
Control Selector b.
NOTE: Should you wish to return the
remote to the original configuration after
entering a Volume Punch-Through, you
will need to repeat the steps shown above.
However, press the same Device Control
Selector in steps one and three.
Re-Assigning Device Control
Selectors
Although each of the seven Device
Control Selectors c is normally
assigned to the category of product shown
on the remote, it is possible to re-assign
one of these buttons to operate a second
device of another type. For example, if you
have two VCRs, but no satellite receiver,
you may program the “SAT” button to
operate a second VCR. Before following
the normal programming steps for either
Three-Digit entry or Auto Search code
entry, you must first re-assign the button
with the following steps:
1. Press the Device Control Selector
c you wish to re-assign and the
Mute button ` at the same time
until the red light illuminates under
the Device Control Selector.
2. Press the Device Control Selector
c for the function you wish to
program into the re-assigned button.
3. Enter the three-digit code for the spe-
cific model you wish the re-assigned
button to operate.
4. Press the same Device Control
Selector pressed in Step 1 again to
store the selection.
Example: To use the SAT button to
operate a second VCR, first press the
SAT Device Control Selector
c, and the Mute button ` at
the same time until the red light
glows under the SAT button. Press
the VCR button, followed by the
three-digit code for the specific
model you wish to control. Finally,
press the SAT button again.
31
AVR35 om (H) 2/5/99 10:41 AM Page 31
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR35 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info