switch should be pressed until it pops out from the
front panel and the word “OFF”is seen at the top of
the switch.
NOTE: This switch is normally left in the “ON”position.
2Power Indicator:This LED lights amber when the
unit is in the Standby mode to signal that the AVR is
ready to be turned on.When the unit is in operation,
the indicator is blue
.
3Standby/On Switch:When the Main Power
Switch
1
is “ON,”press this button to turn on the
A
VR 340;press it again to turn the unit off.The
P
ower
Indicator
2
turns blue when the unit is on.
4Headphone Jack: This jack may be used to listen
to the AVR 340’s output through a pair of headphones.
The speakers will automatically be tur
ned off when the
headphone jack is in use.When configuring your sys-
tem using EzSet/EQ,
the calibration microphone should
be plugged into this jack using the supplied adaptor
that converts the small mini-plug at the end of the
microphone’s cord to a 1/4" plug.
5Tone Mode: This button controls the tone mode
settings,enabling adjustment of the bass and treble
boost/cut.You may also use it to take the tone con-
trols out of the signal path completely for
“flat”
response.The first press of the button displays a
TONEINmessage in the Lower Display Line
ıand in the on-screen display.To take the controls
out of the signal path,
press either of the
‹
‹
/
›
›
Buttons )until the display reads TONEOUT.
To change the bass or treble settings,make sure that
TONE
IN
appears in the Lo
wer Display Line
ı
or press either of the
‹
‹
/
›
›
Buttons )until it does.
Press the Tone Mode Button 5until the desired
option of
TREBLEMODEor BASSMODE
appears in the Lo
wer Display Line
ıand in the
on-screen display and then press either of the
‹
‹
/
›
›
Buttons )to enter the desired boost or cut setting.
Both treble and bass contours may be boosted or
cut by up to + or –10dB in increments of 2dB.
See pages 23 and 34 for more information on the
tone controls
.
NOTE
:
The
A
VR 340 is not equipped with a traditional
Balance control.When listening to two-channel materi-
als,if you wish to adjust the stereo image, you may
use the
Channel Adjust Selector to increase or
decrease the level of the left front channel by up to +
or –10dB, and then to decrease or increase the right
front channel by the corresponding amount.However,
when listening to surround materials and most two-
channel materials,it is recommended that you leave
these settings at the results obtained during the config
-
uration process described on pages 19 through 33.
1Main Power Switch
2Power Indicator
3Standby/On Switch
4Headphone Jack
5Tone Mode
6Speaker Selector
7Surround Mode Group Selector
8Surround Mode Selector
9Tuning Selector
)
‹/›
Buttons
!Tuner Band Selector
@Set Button
#Digital Input Selector
$Preset Station Selector
%Delay Adjust Selector
^Input Source Selector
&Tuner Mode Selector
*Optical 4 Digital Audio Input
(Coaxial 4 Digital Audio Input
ÓVideo 4 Video Input Jacks
ÔVideo 4 Audio Input Jacks
Channel Adjust Selector
ÒVolume Control
ÚInput Indicators
ÛSpeaker/Channel Input Indicators
ÙUpper Display Line
ıLower Display Line
ˆSurround Mode Indicators
˜Remote Sensor Window
DIGITALLOGIC 7
VID 1
DVD
CD
FMAM
TAPE
6 8 CH
VID 2
VID 3
VID 4
PRO LOGIC
3 STEREO
H
EADPHONE
DSP
5 7 CH. STEREO
SURR. OFF
1
2
6
7
#
Ú
(
*
Û
8
)
!
@
)
&
%
3
4
˜
5
9
$
^
Ò
Ó
A
VR 340
ˆ
Ù
Ô
ı
O
ptical 4
Coaxial 4
V
ideo 4
FRONT-PANEL CONTROLS
FRONT-PANEL CONTROLS 55
NOTE: To make it easier to follow the instructions that refer to this illustration,a larger copy may be downloaded from the Product Support section for this product
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Harman Kardon AVR340 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Harman Kardon AVR340 in the language / languages: English as an attachment in your email.
The manual is 1,38 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
