502605
14
Zoom out
Zoom in
Previous page
1/56
Next page
u Tuning Up/Down: When the tuner is in
use, these buttons will tune up or down through
the selected frequency band. If the
Tuner Mode
Button
s^ has been pressed so that the
AUTO Indicator X is illuminated, pressing and
holding either of the buttons for three seconds
will cause the tuner to seek the next station with
acceptable signal strength for quality reception.
When the
AUTO Indicator X is NOT illumi-
nated, pressing these buttons will tune stations
in single-step increments. (See page 31 for more
information.)
v OSD Button: Press this button to activate
the On-Screen Display (OSD) system used to set
up or adjust the AVR 320’s parameters.
w Dolby Mode Selector: This button is
used to select from among the available Dolby
Surround processing modes. Each press of this
button will select one of the Dolby Pro Logic II
modes or Dolby 3 Stereo. When a Dolby Digital
encoded source is in use, the Dolby Digital mode
may also be selected. (See page 26 for the avail-
able Dolby surround mode options.)
x DTS Digital Mode Selector: When a
DTS-encoded digital source is selected, each
press of this button will scroll thorugh the avail-
able DTS modes. The specific choice of modes
will vary according to whether or not the source
material contains DTS-ES 6.1 Discrete encoding.
When a DTS source is not in use, this button has
no function. (See page 40 for the available DTS
Digital options.)
y Logic 7 Selector: Press this button to
select from among the available Logic 7 sur-
round modes. (See page 26 for the available
Logic 7 options.)
z Skip Down Button: This button does not
have a direct function on the AVR 320, but
when used with a compatibly programmed CD
or DVD changer it will change to the previous
disc in the changer or carousel.
` Transport Controls: These buttons do
not have any functions for the AVR 320, but
they may be programmed for the forward/
reverse play operation of a wide variety of CD
or DVD players, and audio or video cassette
recorders. (See page 40 for more information.)
Skip Up Button: This button does not
have a direct function on the AVR 320, but
when used with a compatibly programmed CD
or DVD changer it will change to the previous
disc in the changer or carousel.
Stereo Mode Select Button: Pressing
this button cycles through the stereo modes,
and it is also used to turn off all surround
processing and place the unit in a traditional
two-channel Stereo mode. The first press
selects 5-Channel Stereo, the next press selects
8-Channel Stereo, and the third press selects
“SURROUND OFF, which is true Stereo.
Macro Buttons: Press these buttons
to store or recall a “Macro”, which is a
preprogrammed sequence of commands
stored in the remote. (See page 38 for more
information on storing and recalling macros.)
DTS Neo:6 Mode Select: Pressing
this button cycles the AVR through the various
DTS Neo:6 modes, which extract a five-channel
surround field from two-channel program
material. The first press selects the last
DTS Neo:6 surround mode that was in use,
and each subsequent press selects one of the
other DTS Neo:6 modes.
Disc Skip Button: This button has no
direct function for the AVR 320 but is most
often used to change to the next disc in a CD
or DVD player when the remote is programmed
for that type of device. (See page 37 for more
information on using the remote with products
other than the AVR 320.)
Preset Up/Down: When the tuner is
in use, press these buttons to scroll through the
stations programmed into the AVR 320’s mem-
ory. When some source devices, such as CD
players, VCRs and cassette decks, are selected
using the device
Input Selectors e, these
buttons may function as Chapter Step or Track
Advance.
Clear Button: Press this button to clear
incorrect entries when using the remote to
directly enter a radio station’s frequency.
Memory Button: Press this button to
enter a radio station into the AVR 320’s preset
memory. Once the
MEMORY Indicator U
flashes, you have five seconds to enter a preset
memory location using the
Numeric Keys
r. (See page 31 for more information.)
Delay/Prev Ch.: Press this button to
begin the process for setting the delay times
used by the AVR 320 when processing surround
sound. After pressing this button, the delay
times are entered by pressing the
Set Button
p and then using the
/
¤
Buttons n to
change the setting. Press the
Set Button p
again to complete the process. (See page 23 for
more information.)
Button: Press this button to change a
setting or selection when configuring many of the
AVR 320’s settings.
Speaker Select: Press this button
to begin the process of configuring the
AVR 320’s bass management system for use
with the type of speakers used in your system.
Once the button has been pressed, use the
/
¤
Buttons n to select the channel you
wish to set up. Press the
Set Button p and
then select another channel to configure.
When all adjustments have been completed,
press the
Set Button p twice to exit the
settings and return to normal operation. (See
page 22 for more information.)
Multiroom: Press this button to activate
the multiroom system or to begin the process of
changing the input or volume level for the sec-
ond zone. (See page 36 for more information on
the Multiroom system.)
Volume Up/Down: Press these buttons
to raise or lower the system volume.
SPL Indicator Select: This button acti-
vates the AVR 320’s EzSet function to quickly
and accurately calibrate the AVR 320’s output
levels. Press and hold the button for three
seconds and then release it. Note that the
test tone will begin circulating, and the
Program/SPL Indicator c will change
colors. During this sequence, EzSet will
automatically adjust the output levels for all
channels until they are equal, as shown by
the
Program/SPL Indicator c lighting
green for each channel. Press this button
again when the adjustment is complete to
turn off the test tone. (See page 24 for more
information on EzSet.)
Learn Button: Press this button to begin
the process of “learning” the codes from another
product’s remote into the AVR 320’s remote. (See
page 37 for more information on using the
remote’s learning function.)
Mute: Press this button to momentarily
silence the AVR 320 or TV set being controlled,
depending on which device has been selected.
When the AVR 320 remote is being programmed
to operate another device, this button is pressed
with the
Input Selector Button e to begin
the programming process. (See page 37 for
more information on programming the remote.)
EzSetSensor Microphone: The sensor
microphone for the EzSet microphone is behind
these slots. When using the remote to calibrate
speaker output levels using EzSet, be sure that
you do not hold the remote in a way that cov-
ers these slots. (See page 24 for more informa-
tion on using EzSet.)
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
14 MAIN REMOTE CONTROL FUNCTIONS
Main Remote Control Functions
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR320 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR320 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info