Manual Harman Kardon AVR2600 (page 3 of 63) (English)

502785

Zoom out

Zoom in

1/63

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

Verify Line Voltage Before Use

Your AVR 2600 has been designed for use with 120-volt AC current.

Connection to a line voltage other than that for which it is intended can

create a safety and fire hazard and may damage the unit.

If you have any questions about the voltage requirements for your specific

model, or about the line voltage in your area, contact your selling dealer

before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit.

We do not recommend that extension cords be used with this product. As

with all electrical devices, do not run power cords under rugs or carpets or

place heavy objects on them. Damaged power cords should be replaced

immediately by an authorized service center with a cord meeting factory

specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the

plug; never pull the cord. If you do not intend to use the unit for any

considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the

cabinet may present a shock hazard, and any modification to the product

will void your warranty. If water or any metal object such as a paper clip,

wire or staple accidentally falls inside the unit, disconnect it from the AC

power source immediately, and consult an authorized service center.

CATV or Antenna Grounding

If an outside antenna or cable system is connected to this product, be

certain that it is grounded so as to provide some protection against voltage

surges and static charges. Section 810 of the National Electrical Code,

ANSI/NFPA No. 70-1984, provides information with respect to proper

grounding of the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding conductors, location

of antenna discharge unit, connection to grounding electrodes and require-

ments of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided

to call the CATV (cable TV) system installer’s attention to article 820-40 of

the NEC, which provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the grounding system

of the building, as close to the point of cable entry as possible.

Installation Location

• To ensure proper operation and to avoid the potential for safety hazards,

place the unit on a firm and level surface. When placing the unit on a

shelf, be certain that the shelf and any mounting hardware can support

the weight of the product.

• Make certain that proper space is provided both above and below the

unit for ventilation. If this product will be installed in a cabinet or other

enclosed area, make certain that there is sufficient air movement within

the cabinet. Under some circumstances, a fan may be required.

• Do not place the unit directly on a carpeted surface.

• Avoid installation in extremely hot or cold locations, or in an area that is

exposed to direct sunlight or heating equipment.

• Avoid moist or humid locations.

• Do not obstruct the ventilation slots on the top of the unit, or place

objects directly over them.

• Due to the weight of the AVR 2600 and the heat generated by the ampli-

fiers, there is the remote possibility that the rubber padding on the bottom

of the unit’s feet may leave marks on certain wood or veneer materials.

Use caution when placing the unit on soft woods or other materials that

may be damaged by heat or heavy objects. Some surface finishes may be

particularly sensitive to absorbing such marks, due to a variety of factors

beyond our control, including the nature of the finish, cleaning materials

used, and normal heat and vibration caused by the use of the product,

or other factors. We recommend that caution be exercised in choosing

an installation location for the component and in normal maintenance

practices, as your warranty will not cover this type of damage to furniture.

Cleaning

When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary,

and only after unplugging the AC power cord, wipe it with a soft cloth

dampened with mild soapy water, then a fresh cloth with clean water. Wipe

it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners,

thinner, alcohol or any other volatile cleaning agent. Do not use abrasive

cleaners, as they may damage the finish of metal parts. Avoid spraying

insecticide near the unit.

Moving the Unit

Before moving the unit, be certain to disconnect any interconnection cords

with other components, and make certain that you disconnect the unit from

the AC outlet.

Important Information for the User

This equipment has been tested and found to comply with the limits for a

Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio-frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communication.

However, there is no guarantee that harmful interference will not occur in

a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful inter-

ference, and (2) this device must accept interference received, including

interference that may cause undesired operation.

NOTE: Changes or modifications may cause this unit to fail to comply with

Part 15 of the FCC Rules and may void the user’s authority to operate the

equipment.

UNPACKING

The carton and shipping materials used to protect your new receiver during

shipment were specially designed to cushion it from shock and vibration.

We suggest that you save the carton and packing materials for use in ship-

ping if you move, or should the unit ever need repair.

To minimize the size of the carton in storage, you may wish to flatten it.

This is done by carefully slitting the tape seams on the bottom and collaps-

ing the carton. Other cardboard inserts may be stored in the same manner.

Packing materials that cannot be collapsed should be saved along with the

carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the

carton and other sections of the shipping protection are recyclable. Please

respect the environment and discard those materials at a local recycling

center.

It is important that you remove the protective plastic film from the front-

panel lens. Leaving the film in place will affect the performance of your

remote control.

AVR 2600 OM.qxd 4/29/09 12:10 PM Page 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR2600 in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR2600 Manual

Product: