502597
49
Zoom out
Zoom in
Previous page
1/76
Next page
Half: Applies moderate compression.
Full: Applies the most compression.
When you have finished making adjustments in the Audio Effects menu,
press the Audio Effects Button or the Back/Exit Button to clear the screen.
Video Adjustments
The AVR 254 uses leading-edge Faroudja DCDi Cinema video process-
ing technology, with incoming video upscaled to 1080p (up to 1080i
when component video outputs are used) for outstanding video quality,
even with older analog video sources. Faroudja DCDi Cinema’s Dual 3D
comb filters and 10-bit video processing eliminates the jagged edges
and moiré patterns seen with less advanced processing. Thanks to this
“Torino” video processing chip, on-screen graphics may be generated
in high definition, and blended with the incoming video. This not only
delivers crisp, clear information messages, it allows you to continue to
watch a program while making system adjustments.
The video processor automatically provides the best picture based on
the capabilities of your video display and the incoming source video
signals. However, you may experiment with the Video Modes menu
adjustments to try to improve the picture further.
Video Modes
After you have adjusted the picture settings on your video display, addi-
tional adjustments may be made to the AVR, if necessary, to further
improve the picture. Access these settings from the Video Modes menu.
Press the Video Modes Button on the front panel or remote, and the
screen shown in Figure 66 will appear. The menu may also be accessed
from the Setup Source menu by pressing the Info Settings Button and
selecting the Video Modes line.
Figure 66 – Video Modes Menu
Video Mode: The default setting of Processor Off passes the video
signal through to the display without any processing. Select one of these
processing options to optimize the picture for the current program by
applying adjustments to the brightness, contrast, color and sharpness:
Sports: For sporting events.
Nature: For programs shot outdoors, in a natural setting.
Movie: For movies and many television broadcasts.
Custom: Allows manual adjustment of the picture settings. The
Brightness, Contrast, Color and Sharpness settings will appear on
screen as sliders with values ranging from 0 to 100. The default
setting for each adjustment is 50. Use the
/
Buttons to change
each setting’s value.
Picture Adjust: Use this setting to change the aspect ratio of the
displayed image.
When displaying widescreen (16:9) images on a full screen (4:3)
device, letterbox format will be used, in which black bars may appear
above and below the image (pillarboxing).
When displaying full screen images on a widescreen device, black or
gray bars may appear to the left and right of the image.
Some displays, especially plasma and CRT monitors, may suffer from
“burn-in” when the same image, such as the horizontal or vertical bars,
is left on screen for a long period of time. Use this setting to adjust the
picture so that it fills the display’s screen. The options are:
Auto Fit: The AVR automatically adjusts the image as required to
fit the display’s capabilities.
Height Fit: Adjusts the image to eliminate any bars above or below
it. Bars may remain at the sides.
Width Fit: Adjusts the image to eliminate any bars on the sides.
Bars may remain above and below the image.
Zoom 1x: Displays the image as received from the source. If the
image is in the 4:3 aspect ratio, on widescreen displays pillarbox
format may be used. If the image is in the 16:9 aspect ratio, on full
screen (4:3) displays letterbox format may be used.
Zoom 2x: Stretches the image evenly to completely fill the screen.
The outer portions of the image may be cropped.
Feel free to experiment with this setting for each source until you find
a pleasing display format for each program.
Advanced Video Settings: Press the
or OK Button to display the
Advanced Video Modes submenu (see Figure 67).
Figure 67 – Advanced Video Modes Menu
Noise Reduction: Change this setting from its default of Off to Low,
Medium or High to filter out signal noise.
MPEG Noise Reduction: This setting is designed to address two
specific types of video distortion, mosquito noise and blocking artifacts.
If you see haziness or shimmering around the edges of objects or the
scrolling credits in a film, or if the image appears to “pixellate” into
49
ADVANCED FUNCTIONS
AVR254om.qxd 3/28/08 12:46 PM Page 49
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR254 in the language / languages: English as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info