502590
12
Zoom out
Zoom in
Previous page
1/48
Next page
12
REMOTE CONTROL FUNCTIONS
HDMI 2 and 3
: Each code set controls a source device (VCR/PVR, DVD
player or cable/satellite set-top box) connected to one of these inputs.
AUX
: Controls a device connected to the Auxiliary Input.
Any given button may have different functions, depending on which
component is being controlled. Some buttons are labeled with these
functions. For example, the Sleep Button is labeled for use as the Channel
Up Button when controlling a television or cable box. See Table A10 in the
appendix for listings of the different functions for each type of component.
IR Transmitter Lens
: As buttons are pressed on the remote, infrared
codes are emitted through this lens.
Power On Button
: Press this button to turn on the AVR or another device.
The Main Power Switch must first have been switched on.
Mute Button
: Press to mute the AVR 160’s speaker and headphone
outputs. To end the muting, press this button, adjust the volume, or turn off
the receiver.
Program Indicator
: This LED lights up or flashes in one of three colors as
the remote is programmed with codes.
Power Off Button
: Press to turn off the AVR 160 or another device.
AVR Selector
: Press to switch the remote to AVR device mode.
Source Selectors
: Press one of these buttons to select a source device,
e.g., DVD, CD, cable TV, satellite or HDTV tuner. This will also turn on the
receiver and switch the remotes device mode to operate the source.
AM/FM Button
: Press this button to select the tuner as the source, or to
switch between the AM and FM bands.
6-/8-Channel Input Selector
: Press this button to select the
6-/8-Channel Inputs as the audio source. If a signal is present at the
component video inputs assigned to this source, it will be used. If not, the
receiver will use the video input and remote control codes for the last-
selected analog video source.
Test Tone
: Press this button to activate the test tone for manual output-
level calibration.
TV/Video
: This button has no effect on the receiver, but is used to switch
video inputs on some video source components.
Sleep Button
: Press this button to activate the sleep timer, which turns off
the receiver after a programmed period of time of up to 90 minutes.
Channel Controls
: These buttons have no effect on the receiver, but are
used to change channels on TVs and some video sources.
Volume Control
: Press to raise or lower the volume, which will be shown
in decibels (dB) in the Message Display.
On-Screen Display (OSD)
: Press this button to activate the on-screen
menu system.
Channel Level
: Press this button to adjust the output levels for any
channel so that all speakers sound equally loud at the listening position.
Speaker Setup
: Press this button to configure speaker sizes, that is, the
low-frequency capability of each speaker.
Navigation (
KLM N
) and OK Buttons
: These buttons are used to
make selections within the on-screen menu system, or when accessing the
functions of the four buttons surrounding this area of the remote – Channel
Level, Speaker Setup, Digital Input or Delay.
Digital Input Select
: Press this button to select the specific digital audio
input (or analog audio input) to which the current source is connected.
Delay
: Press this button to set delay times that compensate for placing the
speakers at different distances from the listening position, or to resolve a “lip
sync” issue that may be caused by digital video processing.
NOTE
: The Channel Level, Speaker Setup, Digital Input Select and Delay
functions may also be adjusted using the OSD on-screen menus. In
addition, the EzSet/EQ system may be used to adjust the Channel Level,
Speaker Setup and Delay settings automatically.
Numeric Keys
: Use these buttons to enter radio station frequencies or
to select station presets. Press the Direct Button before entering the station
frequency.
Tuning Mode
: This button toggles between manual (one frequency step
at a time) and automatic (seeks frequencies with acceptable signal strength)
tuning mode. It also toggles between stereo and mono modes when an FM
station is tuned.
Memory
: After you have tuned a particular radio station, press this button,
then the Numeric Keys, to save that station as a radio preset.
Tuning
: Press these buttons to tune a radio station. Depending on whether
the tuning mode has been set to manual or automatic, each press will
either change one frequency step at a time, or seek the next frequency with
acceptable signal strength.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR160 in the language / languages: English as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR160

Harman Kardon AVR160 User Manual - German - 48 pages

Harman Kardon AVR160 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info