Manual Harman Kardon AVR 7000 (page 32 of 48) (English)

34997

Zoom out

Zoom in

1/48

32 ADVANCED FEATURES

Advanced Features

the

‹

›

buttons j until the desired vol-

ume level is shown on the DEFAULT VOL

SET line. Note that this setting may not be

made with the regular volume controls.

NOTE: Since the setting for the turn-on volume

cannot be heard while the setting is being

made, you may wish to determine the setting

before making the adjustment. To do this, listen

to any source and adjust the volume to the

desired level using the regular volume controls

*˙. When the desired volume level to

be used at turn-on is reached, make a note of

the setting as it appears in the lower third of

the video screen or in the Main Information

Display W. (A typical volume level will appear

as a negative number such as –25dB.) When

making the adjustment, use the

‹

›

buttons

j to enter this setting.

Unlike some of the other adjustments in this

menu, the turn-on volume default will remain in

effect until it is changed or turned off in this

menu, even when the unit is turned off.

If you wish to make other adjustments, press

the

⁄

buttons g until the on-screen

›

cursor is next to the RETURN TO MAIN

MENU line. If you have no other adjustments

to make, press the OSD Button s to exit the

menu system.

Semi-OSD Settings

The semi-OSD system places one line messages

at the lower third of the video display screen

whenever the Volume, Input Source, Surround

mode or tuner frequency of any of the configu-

ration settings are changed.The semi-OSD sys-

tem is helpful in that enables you to have feed-

back on any control changes or remote com-

mands using the video display when it is diffi-

cult to view the front-panel displays. However,

you may occasionally prefer to turn these dis-

plays off for a particular listening session. You

may also want to adjust the length of time the

displays remain on the screen. Both of those

options are possible with the AVR 7000.

To turn off the semi-OSD system, you will need

to make an adjustment in the ADVANCED

SELECT menu (Figure 8). To start the

adjustment, press the OSD button s to bring

the main AUDIO SETUP menu to the

screen. Press the

¤ Button g six times, until

the on-screen

¤ cursor is next to the

ADVANCED line. Press the Set Button i

to enter the ADVANCED SELECT menu.

At the ADVANCED SELECT menu make

certain that the on-screen

› cursor is next to

the SEMI OSD DEFAULT line by press-

ing the

⁄

buttons g as needed. Next,

press the

› button so that the word

OFF is highlighted in the video display.

Note that this setting is temporary and will

remain active only until it is changed or until

the AVR 7000 is turned off. Once the unit is

turned off, the semi-OSD displays will remain

activated, even if they were switched off for the

previous listening session.

To change the length of time that the semi-OSD

displays remain on the screen, go to the

ADVANCED SELECT Menu as outlined

earlier, and press the

⁄

buttons g as

needed, until the on-screen

›

cursor is next to

the SEMI-OSD TIME OUT line. Next,

press the

‹

›

Buttons j until the

desired time in seconds is displayed. Note that

unlike most of the other options in this menu,

this is a permanent setting change, and the

time-out entry will remain in effect until it is

changed, even when the unit is turned off.

If you wish to make other adjustments, press

the

⁄

buttons g until the on-screen

›

cursor is next to the RETURN TO MAIN

MENU line. If you have no other adjustments

to make, press the OSD button s to exit the

menu system.

Full-OSD Time Out Adjustment

The FULL-OSD menu system is used to

simplify the setup and adjustment of the AVR

7000 using a series of on-screen menus. The

factory default setting for these menus leaves

them on the screen for 20 seconds after a peri-

od of inactivity before they disappear from the

screen or Time Out. This Time Out is a safety

measure to prevent the menu text from burning

into the CRTs in your monitor or projector,

which might happen if they were left on indefi-

nitely. However, some viewers may prefer a

slightly longer or shorter period before the Time

Out display.

To change the Full-OSD Time Out, you will need

to make an adjustment in the ADVANCED

SELECT Menu (Figure 1). To start the

adjustment, press the OSD button s to bring

the main AUDIO SETUP Menu to the

screen. Press the

¤ button g six times,

until the on-screen

¤ cursor is next to the

ADVANCED line. Press the Set Button i

to enter the ADVANCED SELECT Menu

(Figure 8).

At the ADVANCED SELECT menu make

certain that the on-screen

› cursor is next to

the FULL-OSD TIME OUT line by

pressing the

⁄

Buttons g as needed.

Next, press the

‹

›

buttons j/ until the

desired time is displayed in seconds. Note that

unlike most of the other options in this menu,

this is a permanent setting change, and the

time-out entry will remain in effect until it is

changed, even when the unit is turned off.

If you wish to make other adjustments, press

the

⁄

buttons g until the on-screen

›

cursor is next to the RETURN TO MAIN

MENU line. If you have no other adjustments

to make, press the OSD Button s to exit the

menu system.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 7000 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 7000

Harman Kardon AVR 7000 User Manual - Dutch - 52 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 7000 Manual

Product: