Manual Harman Kardon AVR 4000 (page 26 of 58) (English)

8518

Zoom out

Zoom in

1/58

26 SYSTEM CONFIGURATION

System Configuration

Continue to adjust the individual speakers until

they all have the same volume. Note that adjust-

ments should be made with the

‹/› buttons

on the remote only, NOT the main vol-

ume controls.

You may also adjust the output levels manually

while using the level indication feature of the

EzSet remote. To activate the sensor and indica-

tor, simply press and release the SPL Indicator

Select button

on the remote while the test

tone is circulating. The Program/SPL Indicator

will change color to indicate the level.

Because the remote functions as level sensor, in

that case all further adjustments can be made

with the front panel buttons only, with help of

an assisting person. Adjust the level using the

‹/› buttons

on the front panel until the LED

lights green for all channels. When it is red the

level is too high; when it is amber the level is

too low. Press the SPL Indicator Select

button when you are finished to turn the sensor

and Indicator off.

NOTE: The subwoofer output level is not

adjustable using the test tone. To change the

subwoofer level, follow the steps for Output

Level Trim Adjustment on page 32.

When all channels have an equal volume level,

the adjustment is complete. Now turn the

Volume

down to about -40dB, other-

wise the listening level may be too high as soon

as the source’s music starts to play.To exit this

menu, press the

⁄/¤ buttons

until the on-

screen

› cursor is next to the RETURN TO

MENU line, and then press the Set button

to turn the test tone off and return to the

MASTER MENU.

The output levels may also be adjusted at any

time using the discrete buttons and semi-OSD

system. To adjust the output levels in this fash-

ion, press the Test Tone Selector

.As

soon as the button is pressed, the test tone will

begin to circulate as indicated earlier.The correct

channel from which the test noise should be

heard will be shown in the lower third of the

video screen and in the Main Information

Display

. As an added assist, while the test

noise is circulating, the proper channel position

will also be indicated in the Speaker/Channel

Indicators

by a blinking letter within the

correct channel. Turn up the Volume

until you can hear the noise clearly.

To adjust the output level, press the Selector

buttons on the front panel

or the ‹/› but-

tons

until the desired level is shown in

the display or on screen. Once the buttons are

released, the test noise will begin to circulate

again in five seconds.

When all channels have the same output level,

turn the Volume

down to about -40dB,

otherwise the listening level may be too high as

soon as the source’s music starts to play.After-

wards press the Test Tone Selector

button again to turn the test tone off and com-

plete the process.

IMPORTANT NOTE: The Output level adjust-

ment made will be effective for all inputs, but

only for the actual surround mode selected. To

be effective for any other mode select that mode

(with any input) and repeat the level adjustment

described above. This will also allow you to com-

pensate level differences between speakers, that

may be different with each surround mode, or to

increase or decrease the level of certain speakers

intentionally, depending on the surround mode

selected.

Note: Output level adjustment is not available

for the VMAx or Surround Off mode, as no sur-

round speakers are used (so level differences

between the speakers in the room cannot

occur). But to compensate level differences

between stereo, VMAx and other surround

modes (independently from the input selected)

the outputs can be adjusted with the Level Trim

Adjustment procedure, see page 32, also for the

Surround Off (Stereo) and VMAx modes.

Once the settings outlined on the previous

pages have been made, the AVR 4000 is ready

for operation.While there are some additional

settings to be made, these are best done after

you have had an opportunity to listen to a

variety of sources and different kinds of program

material. These advanced settings are described

on pages 36-37 of this manual. In addition, any

of the settings made in the initial configuration

of the unit may be changed at any time.

As you add new or different sources or speakers,

or if you wish to change a setting to better

reflect your listening taste, simply follow the

instructions for changing the settings for that

parameter as shown above. Note that any

settings changed at any time, also when the

discrete buttons are used only, will be stored in

memory in the AVR4000, also if it´s turned off

completely, unless it will be reset (see page 56).

The settings will either depend on the input

(Speaker configuration, analog/digital input

selection, surround mode) or on the surround

mode selected (speaker output level) or be

independent from any input or surround mode

(crossover, only depending on the front speaker

configuration), as described on previous pages.

Having completed the setup and configuration

process for your AVR 4000, you are about to

experience the finest in music and home theater

listening. Enjoy!

i need circuit diagram for avr 4000 to repair the safety mood Submitted on 1-1-2023 at 14:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 4000 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 4000

Harman Kardon AVR 4000 User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 4000 Manual

Product: