502603
7
Zoom out
Zoom in
Previous page
1/62
Next page
AVR
7
ENGLISH
Rear-Panel Connectors, continued
Rear-Panel Connectors, continued
Composite Video Monitor Out connector: If your TV or video display does not
have an HDMI connector, use a composite video cable (not included) to connect the
AVR’s Composite Video Monitor Out connector to your TV’s composite video input.
NOTE: The HDMI connection to your TV is preferred. If you use the composite video
connection to your TV, you will not be able to view the AVR’s on-screen menus.
Composite Video Record Out connector: Connect an analog video recorder’s video
input connector to the AVR’s Composite Video Rec Out connector. You can record
any composite video input signal. NOTE: To record the audio and video from the
source device, connect the AVR’s Analog Record Output connectors to the analog
video recorder’s audio inputs.
Component Video Input connectors: If any of your video source devices have
component video connectors (and do not have HDMI connectors), using the
component video connectors will provide superior video performance. You will also
need to make an audio connection from the device to the receiver. See
Connect Your
Audio and Video Source Devices
, on page 18, for more information.
SIRIUS
®
Tuner connector: Connect a SIRIUSConnect
satellite radio tuner module
here. (Not included. Available at www.sirius.com.) See
Connect Your Audio and Video
Source Devices
, on page 18, for more information.
12V Trigger connector: This connector provides 12V DC whenever the AVR is on.
It can be used to turn on and off other devices such as a powered subwoofer.
Zone 2 IR Input connector (AVR 3650/AVR 365 only): Connect a remote IR receiver
located in Zone 2 of a multizone system to this jack to control the AVR (and any
source devices connected to the Remote IR Output connector) from the remote
zone.
The Bridge IIIP connector: Connect an optional Harman Kardon The Bridge IIIP
docking station to this input. Insert the plug until it snaps into place in the connector.
IMPORTANT: Connect The Bridge IIIP only with the AVR’s power turned off.
Radio Antenna connectors: Connect the included AM and FM antennas to their
respective terminals for radio reception.
Zone 2 Out connectors: Connect these jacks to an external amplifier to power the
speakers in the remote zone of a multizone system.
Subwoofer connector: Connect this jack to a powered subwoofer with a line-level
input. See
Connect Your Subwoofer
, on page 17, for more information.
Analog Audio Input connectors: Use the AVR’s Analog Audio Input connectors for
source devices that don’t have HDMI or digital audio connectors. See
Connect Your
Audio and Video Source Devices
, on page 18, for more information.
Optical Digital Output connector: Connect a digital audio recorder’s optical digital
input to the AVR’s Optical Digital Output connector. You can record both coaxial and
optical digital audio signals.
Speaker connectors: Use two-conductor speaker wire to connect each set of
terminals to the correct speaker. See
Connect Your Speakers
, on page 17, for more
information.
NOTE: The speaker connectors, also called Assigned Amp speaker connectors-
are used for the surround back channels in a 7.1- channel home theater, or you
can reassign them to a remote room for multizone operation or to front height
channels for Dolby Pro Logic
®
IIz operation. See
Place Your Speakers
, on page
13, for more information.
Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVR’s
Network connector to your home network to enjoy Internet radio and content from
DLNA
®
-compatible devices that are connected to the network. See
Connect to Your
Home Network
, on page 20, for more information.
Main Power switch: This mechanical switch turns the AVR’s power supply on or off.
It is usually left on, and it cannot be turned on or off using the remote control.
AC Input connector: After you have made all other connections, plug the supplied
AC power cord into this receptacle and into an unswitched wall outlet.
RS-232 connector: This connector is used to connect to external control hardware.
Consult a certified professional installer for more information.
IR Remote In/Out connectors (AVR 3650/AVR 365 only): When the IR sensor
on the front panel is blocked (such as when the AVR is installed inside a cabinet),
connect an optional IR receiver to the IR Remote In jack. The IR Remote Out jack
may be connected to the IR input of a compatible product to enable remote control
through the AVR.
Fan Vents: These vents are used by the AVR’s fan to cool the system. Maintain
a clearance of at least three inches (75mm) from the nearest surface to avoid
overheating the unit. It is normal for the fan to remain off at most normal volume
levels. An automatic temperature sensor turns the fan on only when it is needed.
IMPORTANT NOTE: Never block the fan vents. Doing so could allow the AVR to
overheat to dangerous levels.
0295CSK - HK (x65Series) AVR3650_365_2650_265 CORE OM, WORK18 danny.indd 7 01/07/11 11:33:30
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 265 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 265 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 265

Harman Kardon AVR 265 User Manual - German - 62 pages

Harman Kardon AVR 265 User Manual - Dutch - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info