599835
23
Zoom out
Zoom in
Previous page
1/52
Next page
23
AVR
ENGLISH
7. Select “Auto: EzSet/EQ”.
8. If you have a subwoofer connected, select “Yes with Sub.” Otherwise, select “Yes
without Sub.”
9. For AVR 1610S/AVR 161S, or for AVR 1710S/AVR 171S’s in 5.0- or 5.1-channel
systems, select “5.0” or “5.1” in the Speaker Configuration screen. For AVR 1710S/
AVR 171S’s in 7.0- or 7.1-channel systems, select “7.0” or “7.1.”
10. The test will begin. Make sure that the room is quiet while the test noise is playing
through the speakers.
11. When the test finishes, select “Done” to exit.
NOTES:
If there are fewer than five main speakers in your system, do not use the EzSet/
EQ process. Instead, proceed as described in Manual Speaker Setup, on page 30.
If you are using an AVR 1710S/AVR 171S in 6.0- or 6.1-channel configuration with a
single surround back speaker, do not use the EzSet/EQ process. Instead, proceed as
described in Manual Speaker Setup, on page 30.
Set Up Your Sources
The Source Setup menu lets you assign the correct physical audio and video connections
to each source and lets you set many audio and video playback features for each source.
IMPORTANT: The “Video In” and “Audio In” settings are not optional and must
be adjusted before you use your AVR to enable playback of each source. You can
adjust the other settings later. See System Settings, on page 34, for complete information
about adjusting all of the Settings menu options.
1. Review the input connections you listed on the Source Buttons and Assigned
Connectors table, on page 16. Note what changes (if any) you want to make from the
default connector assignments that appear on the list.
2. Turn on your TV and select the TV input where you connected the AVR in Connect Your
TV or Video Display, on page 15.
3. Press the remote control’s OSD/Menu button. The AVR’s OSD setup menu will appear
on the TV. (Note: If you have used a composite video connection to your TV, the OSD
menus will not appear on your TV. Follow the steps below using the AVR’s front-panel
display.)
4. Use the remote’s arrow and OK buttons to select “Source Setup,” and use the left/right
arrow buttons to select a source button with connectors that you want to re-assign.
5. Select “Video In” and select the video input connector you want to assign to the source
button. Press the OK button. NOTE: If you select an HDMI connector as the video input
connector, the audio input connector will automatically change to the same HDMI
connector.
6. If you have not selected an HDMI connector for Video In, select “Audio In” and select
the audio input connector you want to assign to the source button. Press the OK button.
You cannot use a different video input connector with an HDMI audio input connector.
7. Press the remote’s Back/Exit button and repeat steps 3 – 6 for the remaining source
buttons with connectors you want to re-assign.
Title: This selection lets you change the display name for the source, which is useful if
your source’s device type is different from the source’s preprogrammed name. Use the
Up/Down buttons to scroll forward or backward through the alphanumeric characters
until the desired character appears, then use the Left/Right buttons to move the cursor to
the next or previous position. Move the cursor again to leave a blank space. (Your name
can have a maximum of 10 characters.) When you have finished, press the OK Button.
The new name will appear on the AVR’s front panel and throughout the on-screen menu
system.
Tone: This setting determines whether the treble and bass controls are active for the
source. When it’s set to Off, the tone controls are out of the circuit, with no changes to the
sound. When it’s set to On, the bass and treble controls are in the circuit.
Treble/Bass: These settings boost or cut the treble or bass frequencies by up to 10dB,
in 2dB increments. Use the Left/Right buttons to change the setting. The default setting
is 0dB.
Night Mode: This setting activates Night mode for the source, which works with specially
encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that
louder passages are reduced in volume to avoid disturbing others, while dialogue
remains intelligible. The following settings are available:
Off: No compression is applied. Loud passages in the program remain as they were
recorded.
Mid: Loud passages in the program are reduced moderately in volume. Dolby True
HD stream is compressed automatically as set by the incoming stream.
Max: Loud passages in the program are reduced more in volume.
Set Up the AVR
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 1710S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 1710S in the language / languages: English as an attachment in your email.

The manual is 6,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 1710S

Harman Kardon AVR 1710S User Manual - German - 52 pages

Harman Kardon AVR 1710S User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info