502783

Harman Kardon AVR 1565 Manual

19
Zoom out
Zoom in
Previous page
1/41
Next page
19
AVR 1565/AVR 1566
Set Up the AVR, continued,
and Operating Your AVR
5. For each source device you connected to a digital audio input:
a) Use the remote’s Up and Down arrow buttons to select “Source.” Use the Left
and Right arrow buttons to change the listed source to one of the sources you
connected to a digital audio input connector.
b) Use the remote’s down arrow button to select “Audio In.”
* INPUT SETUP *
SOURCE : DVD
TITLE:
AUDIO IN : OPT 1
AUTO POLL : ON
BXR : OFF
TONE : IN
BASS : 0
TREBLE : 0
BACK TO MASTER MENU
c) Use the remote’s Left and Right arrow buttons to select the digital audio input
where you connected the source device.
Additional Input Setup Menu Items
You can also adjust the following settings independently for each source:
Title: You may change the display name for any source (except the radio). This feature
may help you to select the correct source device even when you have forgotten which
physical connections you used.
1. Move the cursor to the Title line and press the OK button. A block cursor will blink.
2. Use the Up/Down buttons to scroll through the alphabet in upper and lower case,
the numbers and many punctuation marks. When you have selected the desired
character, press the Right button to move to the next space. Press the Right button
twice to leave a blank space.
3. Press the OK button when you have finished.
Auto Poll: The Auto Poll feature is used when both an analog audio and a digital audio
connection have been made for one source device. If no digital signal is available, the
AVR will automatically switch to the analog input for the source. This situation can occur
with some cable or satellite television broadcasts, where some channels are broadcast
with digital audio and others with analog audio, or when a DVD player is paused or
stopped.
For some sources such as DVD players, the Auto Poll feature is unnecessary and may be
undesirable. To turn Auto Poll off, move the cursor to the Auto Poll line and press the Left/
Right buttons until Off appears. With Auto Poll turned off, the AVR will check for a signal
only at the audio input assigned to the source.
The remaining Input Setup menu items adjust the AVR’s audio performance for that
source and may be skipped at this time. For most listening, we recommend leaving
these settings at their factory defaults, allowing you to enjoy the sound mix created by
your favorite movie and music artists.
BXR: Enhances bass performance when playing MP3 tracks. Select On, or leave it at the
default Off setting for non-MP3 audio sources.
Tone: This setting determines whether the treble and bass controls are active. When this
line is set to Off, the tone controls are out of the circuit, with no changes to the sound.
When this line is set to On, the bass and treble frequencies are boosted or cut, depending
upon the Bass and Treble settings (see below).
Bass and Treble: Boost or cut the low or high frequencies by up to 10dB by using the
Left/Right buttons to change the setting by 2dB at a time.
When you’re finished, press the remote’s OSD button to turn off the on-screen menu.
Operating Your AVR
Now that you have installed your components and completed a basic configuration, you
are ready to begin enjoying your home theater system.
Controlling the Volume
Adjust the volume either by turning the front-panel Volume knob (clockwise to increase
volume or counterclockwise to decrease volume) or by pressing the Volume Up/Down
buttons on the remote. The volume is displayed as a negative number of decibels (dB)
below the 0dB reference point.
0dB is the maximum recommended volume for your AVR. Although it’s possible to turn
the volume to a higher level, doing so may damage your hearing and your speakers. For
certain more dynamic audio materials, even 0dB may be too high, allowing for damage
to equipment. Use caution with regard to volume levels.
Muting the Sound
To mute all speakers and the headphones, press the Mute button on the remote. Any
recording in progress will not be affected. The MUTE message will appear in the front-
panel display as a reminder. To restore the sound, press the Mute button again, or adjust
the volume.
Listening Through Headphones
Plug the 1/4-inch stereo plug on a pair of headphones into the front-panel Phones
jack for private listening. The default Headphone Bypass mode delivers a conventional
two-channel signal to the headphones. Press the Surround Modes button on the front
panel or use the remote and OSD to switch to HARMAN headphone virtual surround
processing, which emulates a 5.1-channel speaker system. No other surround modes
are available for the headphones.
Selecting a Source
There are two different ways to select a source:
• Press the front-panel Source Select buttons.
• Directly select any source by pressing its Source Selector button on the remote.
The AVR selects the audio and video inputs assigned to the source and any other
settings you made during setup.
The source name, the audio and video inputs assigned to the source, and the surround
mode will appear on the front panel.
Video Troubleshooting Tips
If there is no picture:
• Check the source selection.
• Check all connections for a loose or incorrect connection.
• Check the video-input selection on the TV/display device.
Additional Tips for Troubleshooting HDMI Connections
• Turn off all devices (including the TV, the AVR and any source components).
• Unplug the HDMI cables, starting with the cable between the AVR and the TV, and
continuing with the cables between the AVR and each source device.
• Carefully reconnect the cables from the source devices to the AVR. Connect the
cable from the AVR to the TV last.
• Turn on the devices in this order: TV, AVR, source devices.
NOTE: Depending upon the particular components involved, the complexity of
the required communication between HDMI components may cause delays of
up to a minute in the completion of some actions, such as input switching or
switching between SD and HD channels.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 1565 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 1565 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info