Manual Harman Kardon AVR 1510 (page 21 of 47) (English)

534559

Zoom out

Zoom in

1/47

ENGLISH

AVR

Speakers

This selection lets you program the correct setting for each speaker group. The settings

in this menu affect the remainder of the speaker setup process and the availability of

various surround modes at any time.

Select ON when the speakers are present in the system; select OFF for positions where

no speakers are installed. The Front Left & Right setting is always ON and may not be

disabled.

When you have ﬁnished, press the Back/Exit button.

Crossover

After you return to the Speaker Setup menu, navigate to the Crossover line and press the

OK button to display the Crossover menu.

The AVR will display only those speaker groups you set to On in the Number of Speakers

menu.

Refer to Table A2 to see the crossover frequencies that you wrote down for your

speakers.

For each speaker group, select one of these eight crossover frequencies: Large, 40Hz,

60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the speaker’s crossover frequency is

below 40Hz, select the ﬁrst option, “Large.” This setting doesn’t refer to the speaker’s

physical size but to its frequency response, which is also called “full range.”

We recommend that you set the Subwoofer Crossover to the same frequency you used

for the Front Left & Right speaker setting. If you set the Front Left & Right speakers

to “Large”, we recommend that you experiment with different Subwoofer Crossover

Frequency settings to ﬁnd the one that produces the best blend between the subwoofer

and Front Left & Right speakers with your system in your room.

Write down the settings in Table A2 in the Appendix.

When you have ﬁnished entering the settings, press the Back/Exit button to return to the

Speaker Setup menu.

Select the “Speakers” menu again and note the Subwoofer setting: This setting depends

upon the Crossover setting you selected for the front left and right speakers.

If you set the front speakers to a numeric crossover frequency, the subwoofer Ř

setting will always be Sub. All low-frequency information will always be sent to the

subwoofer. If you don’t have a subwoofer, either upgrade to full-range front left and

right speakers or add a subwoofer at the earliest opportunity.

If you set the front left/right speakers to Large, select one of the three following Ř

settings for the subwoofer:

L/R+LFE: This setting sends all low-frequency information to the subwoofer,

including a) information that would normally be played through the front left and

right speakers and b) the special low-frequency effects (LFE) channel information.

OFF: Select this setting when no subwoofer is in use. All low-frequency information

will be sent to the front left and right speakers.

LFE: This setting plays low-frequency information contained in the left and right

program channels through the front left and right speakers, and directs only the

LFE-channel information to the subwoofer.

Distance

As described above in Step Two, when you measured the distances from each of your

speakers to the listening position, your AVR provides an adjustment that compensates

for the different distances so that the sound from each speaker will reach the listening

position at the proper time. This process will improve the clarity and detail of the sound.

On the Speaker Setup menu, move the cursor to the Distance line and press the OK

button to display the Adjust Speaker Distance menu.

Enter the distance from each speaker to the listening position that you measured in Step

Two and recorded in Table A3 in the Appendix (see page 33). Select a speaker, then use

the Left/Right buttons to change the measurement. You can enter distances between 0

and 30 feet (9.1m). The default distance for all speakers is 10 feet (3m).

The default unit of measurement is feet. To change the unit to meters, select the Unit line

and press the Left or Right button to change the setting.

Step Four – Setting Channel Output Levels

For a conventional stereo receiver, a simple balance control adjusts the stereo imaging

by varying the relative loudness of the left and right channels. In a home theater system

with up to ﬁve main channels plus a subwoofer, achieving proper imaging becomes

both more critical and more complex. The goal is to ensure that each channel is heard

at the listening position with equal loudness (when signals of equal loudness are played

through them).

The Output Adjust menu allows you to calibrate the levels manually, either using the

system’s built-in test tone or while playing source material.

From the Speaker Setup menu select Output Adjust to display the speaker volume

adjustment menu.

All of the system’s speakers will appear with their current level settings. You can adjust

each speaker’s level between –10dB and +10dB in 1dB increments.

Set Up the AVR

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 1510 in the language / languages: English as an attachment in your email.

The manual is 1,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 1510

Harman Kardon AVR 1510 Quick start guide - English - 11 pages

Harman Kardon AVR 1510 User Manual - Dutch - 47 pages

Harman Kardon AVR 1510 User Manual - French - 47 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 1510 Manual

Product: