8522

Harman Kardon AVR 135 Manual

30
Zoom out
Zoom in
Previous page
1/48
Next page
30 PROGRAMMING THE REMOTE
PROGRAMMING THE REMOTE
The AVR 135 is equipped with a powerful remote
control that will control not only the receiver’s func-
tions, but also most popular brands of audio and video
equipment,
including CD players, cassette decks, TV
sets
, cable boxes, VCRs, satellite receivers and other
home theater equipment. Once the AVR 135’s remote
is programmed with the codes for the products you
own, it is possible to eliminate most other
remotes and
replace them with the convenience of a single
, universal
remote control.
Programming Device Codes
The AVR 135 remote is factory-programmed for all AVR
functions, as well as those of most Harman Kardon CD
changers, DVD players, CD players and cassette decks.
In addition, by following one of the methods below, you
may program the remote to operate a wide range of
devices from other manufacturers.
Direct Code Entry
This method is the easiest way to program your
remote to work with different products.
1. Use the tables in the following pages to determine
the three-digit code or codes that match both the
product type (e.g., VCR, TV) and the specific brand
name. If there is more than one number for a
brand, make note of the different choices.
2. Turn on the unit you wish to program into the
AVR 135 remote.
3. Press and hold both the
Input Selector e for
the product you wish to control (e.g., VCR, TV) and
the
Mute Button at the same time. When
the red light under the
Input Selector e stays
lit and the
Program Indicator c turns amber
and begins flashing, release the buttons. It is
important that you begin the next step within 20
seconds
.
4. Point the AVR 135’s remote toward the unit to be
programmed, and enter the first three-digit code
using the
Numeric Keys r. If the unit turns off,
the correct code has been entered. Press the
Input
Selector
e again, and note that the red light
will flash three times before going dark to confir
m
the entry.
5. If the device to be programmed in does NOT turn
off
,
continue to enter three-digit codes until the
equipment turns off. At this point, the correct code
has been entered. Press the
Input Selector e
again and note that the red light under the Input
Selector
e will flash three times before going
dark to confir
m the entr
y.
6. Try all of the functions on the remote to make cer-
tain that the product operates properly. Keep in
mind that many manufacturers use a number of
different combinations of codes, so it is a good
idea to make certain that not only the power
control, but the volume, channel and transport
controls work as they should.
If functions do not
work properly
, you may need to use a different
remote code.
7. If a code cannot be entered to turn the unit off, if
the code for your product does not appear in the
tables in this manual, or if not all functions oper-
ate properly, try programming the remote with
the Auto Search Method.
Auto Search Method
If the unit you wish to include in the
A
VR 135’s remote
is not listed in the code tables in this manual or if the
code does not seem to operate properly, you may wish
to program the correct code using the
Auto Search
method that follows:
1. Turn on the unit that you wish to include in the
AVR 135 remote.
2. Press the
Input Selector e for the type of
product to be entered (e.g., VCR, TV) and the
Mute Button at the same time. Hold both
buttons until the red light under the Input Selector
e stays lit and the Program Indicator c
turns
amber and begins flashing. The next step must
take place while the red light is on, and it must
begin within 20 seconds after the light appears.
3. Point the AVR 135 remote toward the unit to be
programmed, and press either the
⁄
or
¤
Button
n repeatedly. Each press will send out a series of
codes from the remote’s built-in database. When
the unit being programmed turns off, stop pressing
the
⁄ /¤
Buttons n, as that is your indication
that the correct code is in use
.
4. Press the
Input Selector e; the red light under
the Input Selector will flash three times before
going dark to confirm the entry.
5. Try all of the functions on the remote to make cer-
tain that the product operates. Keep in mind that
many manufacturers use a number of different
combinations of codes, and it is a good idea to
make certain that not only the power control
works
,
but also the volume
,
channel and transport
controls, as appropriate. If all functions do not work
properly, you may need to Auto-Search for a dif-
ferent code
,
or enter a code via the Direct Code
Entry method.
Code Readout
When the code has been entered using the Auto
Search method,
it is always a good idea to find out the
exact code so that it may be easily reentered if neces-
sar
y
. You may also read the codes to verify which
device has been programmed to a specific Control
Selector button.
1.
Press and hold both the
Input Selector e
for the device you wish to find the code for and
the
Mute Button at the same time. The
Program Indicator c will turn amber and
begin flashing
, and the red light under the
Input
Selector
e will stay lit. Release the buttons
and begin the next step within 20 seconds.
2.
Press the
Set
Button
p.
The
Program
Indicator
c will then blink green in a sequence
that corresponds to the three-digit code, with a one-
second pause between each digit. Count the num-
ber of blinks between pauses to deter
mine the digit
of the code
. One blink is the number 1, two blinks is
the number 2, and so forth. Ten blinks are used to
indicate a “0.”
Example: One blink, followed by a one-second pause,
followed by six blinks, followed by a one-second
pause, followed by ten blinks indicates that the code
has been set to 160.
For future reference, enter the setup codes for the
equipment in your system here:
DVD ____________ CD ________________
VID1/VCR __________ VID2/TV __________
VID3/CBL ________ VID3/SAT __________
TAPE ______________________________
Macro Programming
Macros enable you to easily repeat frequently used
combinations of commands with the press of a single
button on the
AVR 135’s remote control. Once pro-
grammed, a macro will send out up to 19 different
remote codes in a predeter
mined sequential order
enabling you to automate the process of tur
ning on
your system, changing devices, or other common
tasks. The AVR 135’s remote can store up to five
separate macro command sequences:
one that is
associated with the
Power On Button a and four
more that are accessed by pressing the
Macro
Buttons
.
1. Press the
Mute Button and the Macro
Button
to be programmed or the P
o
wer On
Button
a at the same time. An Input Selector
ef will light red, and the Program
Indicator
c will flash amber.
2. Enter the steps for the macro sequence by press-
ing the button for the actual command step
.
Although the macro may contain up to 19 steps
,
each button press, including those used to change
devices, counts as a step. The
Program Indicator
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
40
41
31
32
30
28
29
25
26
27
28
29
30
24
23
22
21
20
31
37
36
35
34
33
32
31
37
36
35
34
33
32
48
49
50
51
47
46
45
44
43
42
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
40
41
31
32
30
28
29
25
26
27
28
29
30
24
23
22
21
20
31
37
36
35
34
33
32
31
37
36
35
34
33
32
48
49
50
51
47
46
45
44
43
42
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
40
41
31
32
30
28
29
25
26
27
28
29
30
24
23
22
21
20
31
37
36
35
34
33
32
31
37
36
35
34
33
32
48
49
50
51
47
46
45
44
43
42
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
4
0
41
3
1
32
30
28
2
9
25
26
27
2
8
29
30
24
2
3
2
2
21
20
3
1
37
36
3
5
34
33
3
2
31
3
7
3
6
35
34
33
32
48
49
5
0
51
4
7
4
6
45
44
43
42
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
40
41
31
32
30
28
29
25
26
27
28
29
30
24
23
22
21
20
31
37
36
35
34
33
32
31
37
36
35
34
33
32
48
49
50
51
47
46
45
44
43
42
33
34
35
36
37
38
39
40
41
48
49
46
47
44
45
42
43
38
39
40
41
31
32
30
28
29
25
26
27
28
29
30
24
23
22
21
20
31
37
36
35
34
33
32
31
37
36
35
34
33
32
48
49
50
51
47
46
45
44
43
42
AVR 135 OM 12/3/04 12:11 PM Page 30
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon AVR 135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 135 in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 135

Harman Kardon AVR 135 User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info