Manual Harman Kardon AVR 135 (page 20 of 48) (English)

8522

Zoom out

Zoom in

1/48

SYSTEM CONFIGURATIONSYSTEM CONFIGURATION

20 SYSTEM CONFIGURATION20 SYSTEM CONFIGURATION

ence through the use of the delay settings to adjust

the timing for the speaker placement and acoustic

conditions in your listening room or home theater.

The AVR 135’s advanced software enables you to

quickly and easily set delay times without the need to

calculate them using a complex formula. Instead, all

you need to do is measure the approximate distance

between your listening position and each of the

speakers in your system. When you enter those

distances into the AVR’s memory as shown below,

the AVR’s microprocessor does the rest of the work,

calculating the proper delay time. The measurements

need not be accurate to the inch, as the system is

designed to accommodate a typical listening area

rather than require the precise measurement to one

“sweet spot” position.

Due to the differences in the way each surround

mode operates, some modes allow for a greater range

of delay times than others. To avoid problems, we

recommend that delay times be adjusted using the

Dolby Digital mode. If a different mode is selected at

a later time, the AVR 135 will automatically restrict

the delay settings to those required by the surround

mode in use.

Delay times are only adjustable for the Dolby modes,

so you will notice that the

DELAY menu may not

be accessed when any other mode, such as a DTS

or Logic 7 option, has been selected. In addition,

when a non-Dolby Digital mode such as Dolby 3

Stereo or Pro Logic II is selected, adjustments may

be made to the Surround speakers only.

To set the delay time for a specific input, the

DELAY ADJUST menu (Figure 7) should be

visible on your on-screen display. If it is not, press

the

OSD Button v to bring up the MASTER

, and press the

Button n until the

on-screen

›

cursor is pointing at the DELAY

ADJUST

line

. Press the

Set Button p to

call up the menu.

NOTE: In order to adjust the Delay settings for the

surround back channels, a Dolby Digital or DTS source

must be playing. This enables the system to activate

the surround back processing mode.

Figure 7

Once the DELAY

ADJUST

menu is on your

screen, note that the default setting to enter the dis-

tances from the speakers to the listening position is in

feet. If your measurements are in feet, proceed to the

next step;

if your measurements are made in meters,

press the

Button n until the on-screen

›

cursor

is at the

UNIT line on the menu. Then, press the

‹

›

Buttons o so that METER is highlighted.

When the change in measurement units is made,

press the

⁄

Buttons n to retur

n the

›

cursor

to the

CENTER position.

With the on-screen

›

cursor pointing to CENTER,

press the

‹

›

Buttons o until the distance from

the center speaker to the preferred listening position is

entered. Next, press the

Button n to move the

cursor to the

SURROUND line and use the

‹

›

Buttons o again to enter the distance

from the

video display at the front of the room to the surround

speakers. Finally, if the system is configured for 7.1

operation by entering

LARGE or SMALL on

the

SURR BACK line of the SPEAKER

SETUP

menu, press the

Button n again

and use the

‹

›

Buttons o to enter the distance

from the listening position to the surround speakers.

Remember that this last adjustment will only be needed

when you have surround back speakers installed and

Dolby Digital chosen as the surround mode.

When the speaker-to-listening-position distance has

been entered for all active speaker positions, press the

⁄

Buttons n until the on-screen cursor is next

BACK TO MASTER MENU and press the

Set Button p.

The delay settings may be changed at any time

directly from the remote control by pressing the

Delay Button . CENTER DELAY will

appear in the

wer Display Line

¯,

but you

may press the

⁄

Buttons n to select any

of the speaker groups.

Press the

Set Button p when the desired speaker

group appears, and then press the

⁄

Buttons

n again to enter the distance from the speaker to

the listening position.

Press the

Set Button p

again to enter the data.

You may then press the

⁄

Buttons n to select another speaker group to

repeat the procedure

as needed,

or wait five seconds

for the system to return to normal operation.

Output Level

Adjustment

Output level adjustment is a key part of the configura-

tion of any surround sound product. It is particularly

important for a digital receiver such as the

VR 135,

as correct outputs ensure that you hear soundtracks

with the proper directionality and intensity.

IMPORTANT NOTES:

• Listeners are often confused about the operation of

the surround channels. While some assume that

sound should always be coming from each speaker

most of the time there will be little or no sound in

the surround channels. This is because they are

only used when a movie director or sound mixer

specifically places sound there to create ambience

or a special effect,

or to continue action from the

front of the room to the rear. Once the output

levels are properly set, it is normal for surround

speakers to operate only occasionally. Artificially

increasing the volume to the rear speakers may

destroy the illusion of an enveloping sound field

that duplicates the way

you hear sound in a movie

theater or concert hall.

• When the AVR 135 is configured for 6.1-channel

operation using a single surround back speaker, the

output level adjustments will still provide an adjustment

for separate surround back left and surround back right

positions even though your system has only one

surround back speaker. This means that the Surround

Back channel will seem to appear twice, and in 6.1

operation this is normal. The separate SBL/SBR adjust-

ments for 6.1 operation are needed to optimize the

balance between the two discrete channels within the

AVR as they are mixed for output to a single speaker.

Before beginning the output level adjustment process,

make certain that all speaker connections have been

properly made. The system volume should be set to

the level that you will use during a typical listening

session.

Using the Full-OSD System

ollow these steps while seated in the listening posi-

tion that will be used most often:

1. Make certain that all speaker positions have been

properly configured for their “large” or “small” set-

tings (as outlined above) and turn off the OSD

system if it is in use.

2. Adjust the volume so that it is at

-15dB,as

shown in the on-screen display or

wer

Display Line

¯.

3. Output level adjustment is most easily done

through the

CHANNEL ADJUST menu

(Figure 8).

If you are already at the

MASTER

, press the

Button n until the

on-screen

›

cursor is next to the CHANNEL

ADJUST

line. If you are not at the

MASTER MENU, press the OSD Button

v to bring up the MASTER MENU

(Figure 1), and then press the

Button n

until the on-screen

›

cursor is next to the

CHANNEL ADJUST line. Press the Set



* DELAY ADJUST *



FRONT :10FT

CENTER :10FT

SURROUND :10FT

SURR BACK :10FT

UNIT :FEET 



BACK TO MASTER MENU



AVR 135 OM 12/3/04 12:11 PM Page 20

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon AVR 135 in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Harman Kardon AVR 135

Harman Kardon AVR 135 User Manual - Dutch - 42 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Harman Kardon AVR 135 Manual

Product: