640739
2
Zoom out
Zoom in
Previous page
1/2
Next page
NOTE
If another accessory is already using the accessory circuit
connector [4], use a Switched Circuit Adapter Harness (Part
No. 70264-94A, available separately) as a "Y" adapter.
6. Mate the heated seat connector to the accessory circuit
connector [4].
7. Follow the instructions in the Owner's Manual to re-connect
the negative (-) battery cable.
8. Guide the wiring into the space beneath the seat so that
the wiring will not be crimped when the seat is installed.
9. Follow the instructions in the Owner's Manual to install the
seat.
After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)
10. For 1997 through 2005 FLHT/I/C/CI/CUI models: Pro-
ceed to the OPERATION section.
For 2006 and later FLHT/I/C/CI/CUI, and ALL FLTR
models:
a. See Figure 2. Obtain the new passenger grab strap
(1) from the kit, and the saddlebag front mounting
brackets (4), bolts (3) and flat washers (2) removed
earlier.
b. Install the saddlebag front mounting brackets and
grab strap as shown to the chrome frame tube covers.
Finger-tighten the bolts.
c. Follow the instructions in the Owner's Manual to re-
install the left-side and right-side saddlebags.
d. Tighten the mounting bolts to 60-96 in-lbs (7-11 Nm)
after seating the saddlebags.
2
3
1
4
is01041
1. Passenger grab strap
2. Original equipment flat washer
3. Original equipment hex head bolt
4. Forward saddlebag mounting bracket
Figure 2. Grab Strap and Saddlebag Front Mounting
Bracket
OPERATION
NOTE
The accessory switch is a rocker switch found on the inner
fairing switch panel.
1. With the ignition/key switch at IGNITION or ACCESS,
open the circuit to the heated seat by flipping the
accessory switch from OFF to ON.
2. Two switches on the side of the seat control the rider and
passenger heating areas independently. The forward
switch controls the rider area, and the rearward switch
controls the passenger area.
a. In the center position, the heat to that area of the seat
is OFF.
b. Pressing the lower part of the switch in toward the
seat turns the heat in that area ON at the LOW set-
ting.
c. Pressing the upper part of the switch in toward the
seat turns the heat in that area ON at the HIGH set-
ting.
NOTES
If the accessory switch is left ON and a seat heater rocker
switch is left in either the LOW or HIGH position when the
motorcycle is turned off, the seat will begin heating when the
ignition/ key switch is turned to the IGNITION or ACCESS
position.
A seat heater in operation while the motorcycle engine is
turned off or running below normal operating speed can
quickly discharge the vehicle battery, which could lead to
a subsequent failure to start, and could damage the elec-
trical system.
1
3
2
4
is01042
1. Rider section heat control switch
2. Passenger section heat control switch
3. Low heat position
4. High heat position
Figure 3. Seat Heating Control Switches
-J03893 2 of 2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harley-Davidson J03893 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harley-Davidson J03893 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info