711487

Hanseatic WQP8-J7710D Manual

65
Zoom out
Zoom in
Previous page
1/72
Next page
Page EN-29
Installation, fitting, connection and initial commissioning
Adjusting the water hardness
level
Hard water will cause calcification within
the dishwasher. Also, more dishwasher de-
tergent will be required to clean the dishes.
Soft water increases foaming. For this rea-
son, the degree of hardness of the water
has to be determined and adjusted even
before the first use. You can determine the
water hardness from your water bill or en-
quire about the degree of hardness at the
water supply company. The appliance is
set to a hardness level of “
H3
“ in the factory.
Water hardness
°dH Display
0-5
H1
6-11
H2
12-17
H3
18-22
H4
23-34
H5
35-55
H6
(1) (6)
(8)
(13)(14)
Do not allow more than 1 minute to elapse
between the following actions, otherwise the
adjustment process will be interrupted.
1. Close the dishwasher door.
2. Switch it on with the On/Off button (1).
The display (8) is initially fully lit up. After
a short time, the programme symbol (10)
for the ECO programme comes on.
3. Hold the start/pause button
(6) in until
the displays (13) and (14) blink alter-
nately.
The display (8) shows the current hard-
ness level (
H1
to
H6
),
4. Press the start/pause button (6) as
many times as necessary to display the
required hardness level.
5. Around 5 seconds after you push it for the
last time, the dishwasher will automatical-
ly revert to the normal display.
The hardness level setting is saved.
Test run
It is recommended that you carry out a test
run before the first dishwasher cycle in order
to remove residues from the manufacturing
process and in order to ensure that the de-
vice functions perfectly. Carry out this test run
when the dishwasher is empty and without
any dishwasher detergent.
1. Open the valve completely.
2. Close the dishwasher door.
3. Switch the dishwasher on using the but-
ton
(1).
All the lights initially come on on the
display (8). After a short time, the pro-
gramme symbol (10) for the ECO pro-
gramme comes on.
4. Start the programme with the button
(6).
The programme begins after a few sec-
onds.
5. Check for water leaks and unusual nois-
es.
6. When the programme ends, an acoustic
signal sounds 8 times.
Switch the dishwasher off using the but-
ton (1).
7. Slightly open the door to allow the moist
air to escape.
8. Close the valve.
… 65 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hanseatic WQP8-J7710D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hanseatic WQP8-J7710D in the language / languages: English, German as an attachment in your email.

The manual is 6,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info