711503
57
Zoom out
Zoom in
Previous page
1/67
Next page
Page EN-23
Installation and connection
Connect the outlet hose’s outlet as follows:
Ø ≥ 40 mm
max. 1000 mm
Option A:
Direct connection to the odour seal (siphon)
of your washing/dishwashing basin. The out-
let hose must be a maximum of 1000 mm
above the floor.
Option B:
Connection to a floor drain.
Connecting the inlet hose
NOTICE
Risk of damage!
The dishwasher is set up for a water
pressure of 0.4bar to 10bar (0.04MPa
to1.0MPa). Water must always be able
to run freely into the dishwasher, other-
wise this can damage the appliance.
For water pressure of less than 10 bar,
install a pressure reducer (in case of
doubt, seek information from the wa-
ter supply company).
Never connect the appliance to the
water tap or the mixing arm of a wa-
ter heater (e.g. continuous fl ow heat-
er, pressure-free boiler etc.).
Ensure that the inlet hose is correctly
connected and is not kinked or dam-
aged.
Do not damage the inlet hose; it con-
tains electrical components. If the
inlet hose is damaged, contact our
service department (see „Service“ on
page EN-31).
3
¾ inch
Inlet hose
For water supply, you need a water tap with
a ¾ inch screw connector.
1. Screw the safety valve’s lock nut to the
tap hand-tight.
2. Check that the connection to the water
tap is sealed. Turn on the water tap slow-
ly and ensure that no water is escaping.
Then close the valve again.
Connecting the dishwasher to
the electricity
WARNING!
Electric shock / fi re hazard!
Prior to connecting the dishwasher,
ensure that you have taken note of all
the safety instructions and adhered
to them (page EN-6 ).
Depending on the recess into which the dish-
washer will be fitted, the dishwasher should
be connected before or after fitting.
For the electrical connection of the dish-
washer, a professional must install an
earthed power socket with its own fuse of
a sufficient size (230 V~/50 Hz/10 A).
The plug must be installed in such a way
that the recess into which the dishwasher
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hanseatic WQP8-7736B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hanseatic WQP8-7736B in the language / languages: English, German as an attachment in your email.

The manual is 3,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info